What kind of nails should I use for fascia?

Hardie Trim

It calls for 2-inch, 16-gauge, corrosion-resistant finish nails only when you are attaching fascia to double sub-fascia. Nails should not be closer than 1 1/4 inches from the edges and no nearer than one inch from the ends. With pneumatic nailing, Hardie Trim recommends driving the finish nails flush.

Also asked, where do you nail your fascia?

Begin installing aluminum fascia at the center of each length by pushing it up snug to the bottom of the soffit panels. Nail it, then work your way in both directions, driving nails every 16 in., placed about 1 in. from the top and bottom. Overlap joints 1 to 2 in.

Furthermore, what is the best wood to use for fascia board? Wood Is a Common Fascia Material Cedar is a popular fascia wood and redwood is another. That's because both species resist rot and moisture very well, even when unpainted. If you prime and paint the fascia, you can also make them out of fir, spruce or pine, which are all less expensive.

Correspondingly, can you nail vinyl fascia?

Do not nail vinyl fascia under any circumstances. When overlapping fascia panels, first cut a notch in the underlying panel.

How much do you overlap fascia?

Overlap Each Section Each piece should overlap the previous section of aluminum fascia by 1 to 2 inches, but the overlap should be a smooth transition that doesn't cause bumps or raised areas. Be sure that the cuts are straight, and follow the correct angles.

37 Related Question Answers Found

What material is used for fascia?

Wood

Can you bend vinyl fascia?

When the vinyl expands it will pucker around the nails. Coil stock is a roll of flat aluminum you bend with a metal bender as needed. You can buy pre bent aluminum fascia which is easy to work with and fast to install.

What is vinyl fascia?

Fascia board is the flat horizontal board along the edge of a roof. The fascia is nailed to the ends of the roof rafters, and is used to attach a gutter to the roof and soffit panels underneath the eaves. When installing new vinyl siding on your home, you can install vinyl trim on the fascia.

Which is better vinyl or aluminum soffit?

Vinyl also has a higher impact resistance than aluminum which adds to its durability. When used under eaves, it helps to improve insulation. Less energy is utilized to heat and cool the house which brings down your energy costs with time. Vinyl soffit is low maintenance yet it keeps in good shape for a long time.

How much does it cost to install aluminum fascia?

Typical costs for vinyl or wood fascia boards and soffits range from $6 to $10 per linear foot, and the cost to fit out a simple single-level home is anything from $600 to $2,000. The price of aluminum fascia ranges from $8 to $20 or more, and the budget for a single-story home ranges from $800 to $6,000.

What is F channel used for?

F-channel is used to hold the soffit onto your house. Soffit is the vinyl siding that makes a ceiling under an overhang. The F-channel is a thin vinyl strip that is sold where siding is sold. The upside down F creates a shelf for the soffit to slide into and rest on.

Can soffit be installed on an angle?

soffit vents on angle. The house has very deep eaves, and the windows are set high on the wall, so it was impossible to box the eaves so that the soffits are parallel to the ground. In other words, the soffits are installed parallel to the roof line.

How is soffit attached?

In most instances the cornice or eave of today's homes are finished off with a soffit—the covering on the underside of the overhang. On narrow eaves the rafter ends serve to fasten the soffit and fascia. A ledger plate is fastened to the wall to attach the soffit at that location.

Is sub fascia necessary?

Floor Plans. Sub-fascias are not required by code. The fascia can be nailed directly to the truss tails, but while the sub-fascia is typically a t.

How thick should fascia boards be?

Replacement fascias do vary in thickness by manufacturer, but the rule of thumb is that to qualify structurally as a replacement board they should be somewhere between 16mm and 25mm thick - our most common range is the 18mm Replacement Fascia.

How do you attach fascia to roof trusses?

Nail the first fascia board in place with 2-inch finish nails and a hammer. Drive at least two nails through the fascia into the end of each joist. Butt the next fascia piece to the open end of the first so that it it aligned with the center of the joist where the first board ends.

How do you replace fascia with drip edge?

Removing Drip Edge Eave Strips:

Gently lift up the shingles along the lower edge of the roof, and find the nails attaching the eave strip to the roof decking.
Use a flat pry bar and hammer to remove the nails holding the eave strip to the roof decking.
Slip the eave strip out from under the shingles.

How do you attach fascia to rafters?

Instructions for How to Attach Fascia Board to Roof Trusses

Use the carpenter's square and pencil to put a straight line at the mark. Cut the board with a miter saw. Position the board against the trusses and nail it in place. Put at least 2 nails at both ends of the fascia board into the joists.

How much does it cost to replace rotted fascia?

Replacing your soffit generally costs about $20 to $30 a linear foot installed, while replacing your fascia costs about $15 to $25 a linear foot installed. Prices for the project depend on a number of factors, including the materials used and the size of your house.

How do you seal fascia boards?

Start at the end of a fascia board and caulk the corner edge where two boards meet. Smooth the caulk bead with your finger and begin caulking the joint between the fascia board and the soffit (also known as the eave). Slowly move down the joint to apply a steady bead of caulk into the gap.

Does fascia board need to be treated?

Purchase pressure-treated lumber to replace your fascia boards as a way to extend the life of the repair. Pressure-treated lumber is designed for outside applications and resists rot, moisture and insect damage. Cut the new lumber to size and secure it to the rafter ends with galvanized finish nails.

Do roofers replace fascia?

Soffit, Fascia, Gutter, and Eaves Replace & Repair Estimator

Most often, you'll want to replace your fascia when you replace or repair gutters. Most licensed contractors can typically repair or install all three. Contractors will typically charge by the project, ranging anywhere from a $600-$6,000.