What are fascia boards made of?

Asked By: Iwona Valares | Last Updated: 27th February, 2020
Category: medical health skin and dermatology
4.9/5 (72 Views . 37 Votes)
Typically consisting of a wooden board, uPVC or non-corrosive sheet metal, many of the non-domestic fascias made of stone form an ornately carved or pieced together cornice, in which case the term fascia is rarely used. The word fascia derives from Latin fascia meaning "band, bandage, ribbon, swathe".

Click to see full answer

Thereof, what is the best material for fascia boards?

Cedar is a popular fascia wood and redwood is another. That's because both species resist rot and moisture very well, even when unpainted. If you prime and paint the fascia, you can also make them out of fir, spruce or pine, which are all less expensive. You construct fascia boards out of 1-inch lumber.

Beside above, what are fascia boards? The fascia board is the long, straight board that runs along the lower edge of the roof. The fascia is fixed directly to the lower ends of the roof trusses and usually does all the work of supporting the lower edge of the bottom row of tiles. The fascia board also carries all the guttering.

Also know, what material is used for fascia boards?

Wood is the most common material used to make fascia. Typically, wood fascia boards are made of spruce, pine or fir. However, cedar fascia boards (same wood for decks) are gaining steam.

How thick should fascia boards be?

Replacement fascias do vary in thickness by manufacturer, but the rule of thumb is that to qualify structurally as a replacement board they should be somewhere between 16mm and 25mm thick - our most common range is the 18mm Replacement Fascia.

33 Related Question Answers Found

Why do fascia boards rot?

The rotting condition of the fascia is a sign that water has compromised the structural integrity of the fascia board. There are many factors that can compromise the integrity of fascia boards, but two of the most common are improper installation of drip edge and gutters.

Are fascia boards necessary?

Fascia is meant to protect the roof and the interior of the home from moisture by blocking it from entry. It does have an aesthetic role as well; it creates an even appearance along the roof's edge. If water gets behind the fascia board, it is vulnerable to damage.

How much should it cost to replace fascia boards?

"When the water backs up, the first place it wants to go is the fascia board." Replacing your soffit generally costs about $20 to $30 a linear foot installed, while replacing your fascia costs about $15 to $25 a linear foot installed.

How much does aluminum fascia cost?

Typical costs for vinyl or wood fascia boards and soffits range from $6 to $10 per linear foot, and the cost to fit out a simple single-level home is anything from $600 to $2,000. The price of aluminum fascia ranges from $8 to $20 or more, and the budget for a single-story home ranges from $800 to $6,000.

What is the best material for exterior trim?

Wood. The most classic choice for exterior house trim is wood. Solid wood, as well as composite options, are available. Many homeowners prefer wood trim because of its natural look and feel but quality wood products are becoming scarcer, and therefore more expensive.

How do I protect my fascia board?

Your fascia boards bridge the gap between your roof and your gutter.

Taking Care of Your Fascia Boards
  1. Make sure that you choose excellent products.
  2. Use galvanized nails.
  3. Don't nail them in a way that will split the board over time.
  4. Paint them when possible, or add wood hardener.

How do you fix fascia boards?

Fascia roof repair tips
  1. Choose the best wood. Handpick each wood fascia board and make sure it's from a species of wood that's naturally decay resistant.
  2. Watch where you nail your fascia. If at all possible, never nail a fascia board near the edge of the end grain.
  3. Use the best nails.
  4. Paint the ends of your fascia boards.

What nails do you use for fascia?

Hardie Trim
It calls for 2-inch, 16-gauge, corrosion-resistant finish nails only when you are attaching fascia to double sub-fascia. Nails should not be closer than 1 1/4 inches from the edges and no nearer than one inch from the ends. With pneumatic nailing, Hardie Trim recommends driving the finish nails flush.

What kind of wood should I use for exterior trim?

A common trim board is pressure-treated southern yellow pine. It is inexpensive and widely available, but it tends to warp when it absorbs moisture. Unlike cedar and redwood, southern yellow pine is less stable and wood-eating insects consider it delicious food.

What is the board behind the gutter called?

The board that rests behind your gutter is called a fascia board. So, it's little wonder that fascia boards rot out as frequently as they do.

Can I use pressure treated wood for fascia?

Purchase pressure-treated lumber to replace your fascia boards as a way to extend the life of the repair. Pressure-treated lumber is designed for outside applications and resists rot, moisture and insect damage. Cut the new lumber to size and secure it to the rafter ends with galvanized finish nails.

Can you use Hardie board for fascia?

HardieTrim boards provide unmatched durability and allow you to create a variety of design possibilities for trim, gables, corners, fascia, windows, doors, column wraps, rakes, friezes, decorative trim and other non-structural architectural elements.

What timber do you use for fascia boards?

Timber: Popular hardwood and softwood timber species for fascia board are western red cedar European oak, Utile, Iroko, Douglas fir, Larch and Accoya. The latter is an extremely durable sustainable option.

How thick are soffits?

Standard soffit material is 3/8- or 1/2-inch-thick exterior plywood in pine (or similar softwoods) or cedar. Common, but much less durable, is Masonite or similar fiberboard soffit, as well as much more weather-resistant fiber-cement.

How do I know my fascia size?

Multiply the 1-1/2 inch width of the fascia board by the slope of the roof (e.g. 4/12). 1.5” times 4 divided by 12 = 0.5 or ½ inch. For a 2×6 fascia board at a 4/12 slope, the trim size would be 1-1/2 inch x 5 inches for an overhang without a soffit.

What is the difference between fascia and eaves?

is that fascia is a wide band of material covering the ends of roof rafters, sometimes supporting a gutter in steep-slope roofing, but typically it is a border or trim in low-slope roofing while eaves is the underside of a roof that extends beyond the external walls of a building.

Is fascia considered trim?

Fascia: Vertical roof trim located along the perimeter of a building, usually below the roof level, to cover the rafter tails at the eaves and to seal off the top of the siding along the rake; also called gutter boards.