What is fascia and gutter?

Asked By: Gianpaolo Sibille | Last Updated: 1st June, 2020
Category: medical health skin and dermatology
4.7/5 (72 Views . 20 Votes)
About Fascia Gutters
A fascia gutter is a type of gutter that combines the gutter with the fascia into one system. As it is an all in one thing, the gutter is meant to be installed directly to the roof rafters without the need for the traditional timber fascia. It is alternatively known as an eaves gutter.

Click to see full answer

Similarly one may ask, do gutters need fascia?

Homes like these don't usually have a fascia where gutters can be attached to. Unfortunately, weather can be unpredictable, so if you have a house where the roof overhangs at around 3-4 feet without a basement, a gutter system is required.

Subsequently, question is, how are fascia boards attached? Instructions for How to Attach Fascia Board to Roof Trusses Remove old fascia boards including old nails that are sticking out. Starting at a roof corner, lift the first board into place and hold its top edge tightly against the bottom edge of the roof deck. Position the board against the trusses and nail it in place.

Similarly, you may ask, what is the purpose of a fascia board?

The primary function of the fascia is to protect the roof and the interior of the home from moisture by blocking its entrance. Fascias also play an aesthetic role, because they create a smooth, even appearance along the roof's edge. House fascia can be vulnerable to damage if water gets behind the board.

What is the difference between gutter and Eavestrough?

An eavestrough can be defined as a trough that you see attached to the eaves of a building. This system together helps in draining water from the roof. And the gutter is a channel that also drains water, however, it's a channel that is prepared on the surface. While, the gutter runs along the side of the road.

34 Related Question Answers Found

Can you hang gutters without fascia?

A home without fascia needs to have gutters attached by roof straps. These straps act as a sling for your gutter. They're fitted to the gutter hanger, and then they are attached directly to the roof. Instead, they're a solution for your gutters, so that you can add gutters to a home without worry.

How do you fix fascia behind gutters?

Remove the gutters from the areas where you are going to replace the fascia board. Common residential gutters are installed using long nails that secure the gutter to the facial board. To remove them, carefully pry the nails away from the gutter using the pry bar or hammer claw.

Do roofers replace fascia?

Soffit, Fascia, Gutter, and Eaves Replace & Repair Estimator
Most often, you'll want to replace your fascia when you replace or repair gutters. Most licensed contractors can typically repair or install all three. Contractors will typically charge by the project, ranging anywhere from a $600-$6,000.

What is the best material for fascia boards?

Cedar is a popular fascia wood and redwood is another. That's because both species resist rot and moisture very well, even when unpainted. If you prime and paint the fascia, you can also make them out of fir, spruce or pine, which are all less expensive. You construct fascia boards out of 1-inch lumber.

Is fascia board necessary?

Fascia is meant to protect the roof and the interior of the home from moisture by blocking it from entry. It does have an aesthetic role as well; it creates an even appearance along the roof's edge. If water gets behind the fascia board, it is vulnerable to damage.

How much does it cost to replace fascia boards?

"When the water backs up, the first place it wants to go is the fascia board." Replacing your soffit generally costs about $20 to $30 a linear foot installed, while replacing your fascia costs about $15 to $25 a linear foot installed.

Why is water dripping between gutter and fascia?

If water is dripping behind your gutter, it's probably because it was installed without any flashing over the back of the gutter. The gutter apron will prevent the dripping. A gutter apron is a bent piece of flashing that tucks up under the shingles and over the gutter.

What is the difference between trim and fascia?

is that trim is (uncountable) decoration; especially, decoration placed along edges or borders while fascia is a wide band of material covering the ends of roof rafters, sometimes supporting a gutter in steep-slope roofing, but typically it is a border or trim in low-slope roofing.

What size fascia do I need?

Replacement fascias do vary in thickness by manufacturer, but the rule of thumb is that to qualify structurally as a replacement board they should be somewhere between 16mm and 25mm thick - our most common range is the 18mm Replacement Fascia.

How do you pronounce the word fascia?

noun, plural fas·ci·ae [fash-ee-ee] for 1, 3–5; fas·cias [fey-shuh z] for 2. a band or fillet, as for binding the hair. Also called fascia board. facia.

Is fascia part of roof?

Roofing Parts-The Purpose of the Fascia & Soffit. Every part of your roofing structure has a lot to do with keeping your home dry and comfortable. Fascia, on the other hand, is a part that can easily be damaged. It is the parallel edge that is connected to the ends of the trusses or rafters.

How do I protect my fascia board?

Your fascia boards bridge the gap between your roof and your gutter.

Taking Care of Your Fascia Boards
  1. Make sure that you choose excellent products.
  2. Use galvanized nails.
  3. Don't nail them in a way that will split the board over time.
  4. Paint them when possible, or add wood hardener.

How do you fix fascia?

Fascia roof repair tips
  1. Choose the best wood. Handpick each wood fascia board and make sure it's from a species of wood that's naturally decay resistant.
  2. Watch where you nail your fascia. If at all possible, never nail a fascia board near the edge of the end grain.
  3. Use the best nails.
  4. Paint the ends of your fascia boards.

How do you cut angles for fascia?

Set the angle of a miter saw to 45 degrees so you can make clean cuts through the board. Put on your safety glasses, and position the fascia board so the corner on one end lines up with the saw blade. Turn the saw on and pull it down to cut the angle. Cut the ends of any other boards that will be on a corner.

Are gutter guards worth it?

When you compare this cost to the cost of having gutter guards installed, it should become clear quickly that gutter guards are not worth it. They are expensive, ineffective, easily damaged, and don't even do what they are supposed to do.