What is Schluter trim?

Asked By: Pasqualino Porfiriev | Last Updated: 3rd May, 2020
Category: hobbies and interests woodworking
4.1/5 (124 Views . 25 Votes)
Schluter ®-JOLLY is a finishing and edge-protection profile for the outside corners of tiled surfaces on walls. The vertical wall section of the profile provides a decorative finish and protects adjacent tiles.

Click to see full answer


Then, what is a Schluter strip?

The schluter strip are metal strips used with tile installations. Most commonly, the schluter strip is used to form the edge of a tile installation. This strip will give a square edge rather than a bullnose tile edge. They can be used as a decorative element within the tile pattern, as a border or divider.

Furthermore, what is tile trim called? Bullnose tile is recognizable because of its characteristic rounded edges. It's viewed as an edge treatment or trim piece, and is often used to cover corners or frame the perimeter of a tile design. This eliminates sharper angles and unfinished tile sides from being visible on your floor or wall.

Beside this, how do you finish tile edges?

To give the edge a clean, water-tight finish, place a piece of masking tape one grout joint away from the edge of the last tile. Fill this gap between the tile and the masking tape with a smooth bead of caulk. This will finish the edge without extra tiles.

Is bullnose tile outdated?

Yes, the bullnose pieces are expensive and, yes, they do add up. So they simply don't use any bullnose and you're looking at the edge of the tile as the finished product. Worse still is the DIYer tries to grout the edge to make it look more finished.

38 Related Question Answers Found

What is Schluter trim made of?

The profile is available in chrome-plated solid brass, color-coated aluminum, textured color coated aluminum, anodized aluminum and PVC. Schluter®-SCHIENE features the same design as JOLLY and is also available in solid brass, aluminum, and stainless steel.

What is Schluter made of?

Schluter ®-DITRA and DITRA-XL are specifically designed for ceramic and stone tile installations. DITRA and DITRA-XL provide uncoupling to prevent cracked tile and grout. Made of polyethylene, DITRA and DITRA-XL serve as a waterproofing layer that protects moisture-sensitive substrates, such as plywood/OSB.

What color is Schluter?

Four new colors are being added to Schluter®-DILEX profiles: Dark Anthracite, Grout Grey, Stone Grey, and Cream.

What is a jolly in tile?

Jolly trim is a linear trim or edge for tile. It can be ceramic or metal. It is used to finish a raw tile edge just like a bullnose tile. It can also be used as a liner to accent your design. It's generally very narrow and long with a minimal profile, measuring about ½ x 12 x ¼.

How do you finish tile edges on a backsplash?


Complete the edge by applying a piece of painter's tape to the wall next to the tiles. Squeeze a thin line of caulk down the outside edge of the tiles where they meet the wall. This blends the tiles into the wall, giving it a clean, finished look.

Does Home Depot sell Schluter?

Schluter - Tile Edging & Trim - Tile Tools & Supplies - The Home Depot.

Can you paint Schluter trim?

you can paint it just fine. but, you can use the Schluter edging. just cut off the part that would go under the tiles. rough up the unseen surface.

How deep is a shower niche?

It allows the niche to fit between studs which are often 16 inches apart. With a glass shelf at 12 inches this creates 2 feet of shelf space. The typical depth of a shower niche is 3.5 inches, the width of a wood stud.

What is a Schluter edge?

Schluter ®-RONDEC. Schluter ®-RONDEC is a finishing and edge-protection profile for tiled edges and outside corners of tiled surfaces. The reveal of the profile forms a symmetrically rounded corner along the surface edge.

Should tile overlap in corners?


All you have to do is to start installing wall tile on one side of the corner. When you tile the other side of the corner, the tiles should overlap, but make sure you leave a clearance gap between them (place a spacer).

Where should the backsplash tile end?

Typically, the counter, upper cabinets and wall all end at different places on the sides, leaving no definitive stopping point. In this example, the tile ends at the corners instead of wrapping onto the small wall with the doorway.

Does subway tile need bullnose?

Unless your tiles butt into walls on all sides, you will need some sort of edge trim. Some ceramic lines offer bullnose tiles. A bullnose tile will look like a field tile, except it will have one finished edge. Some lines even offer corner bullnose which are finished on two sides.

Which tile is best for stairs?

Many natural stones tile are available but need to think of the safely in choosing the tile staircase flooring, because marble and terrazzo are slippery but the Ceramic is the better option. Laminate Flooring: Is also the best with low maintenance with stylish luxurious look to the interior design to the home.

Can you sand ceramic tile edges?

Manually Sanding
The rougher the edge on the ceramic tile, the lower the grit of sandpaper needed to smooth it out. Once the edge has been dulled, work your way up to 200-grit sandpaper and then 400-grit sandpaper to polish the edge for maximum smoothness.

What is a bullnose edge?


Bullnose trim is used to provide a smooth, rounded edge for countertops, staircasesteps, building corners, verandahs, or other construction. Masonry units such as bricks, concrete masonry units or structural glazed facing tiles may be ordered from manufacturers with square or bullnosed corners.

What is a pressed edge tile?

Pressed edge (other names include cushion edge, round edge, soft edge, etc.) are tiles that have been manufactured using standard pressing processes in moulds that will result a slight curving on the sides. Minimum grout joint size on these tiles is 3mm.

Is tile trim necessary?

If natural stone tiles are used, and cuts are neat, then there is no need to use a trim as the tile colour is the same all the way through. However, modern porcelain tiles with a digital printed surface, will be clay colour on exposed edges, therefore a plastic or metal trim should be used.