When would you use recirculate on pool filter?

RECIRCULATE. This setting is used to bypass the filter during certain pool cleanups and chemical treatments when you don't want the water contaminating the sand. Water enters the valve through the "PUMP" port and exits back to the pool through the "RETURN" port.

In respect to this, why would you use recirculate on pool filter?

Reviewing Recirculation The recirculate setting on a swimming pool filter is actually used to bypass the filter mechanism. Recirculate allows the water to flow out of the pool and back into it again without running through the sand or diatomaceous earth in the filtration system.

Subsequently, question is, can you shock a pool on recirculate? Shocking The Pool With Powdered Shock Using “Re-circulate”: Once you start slowly pouring the shock into the skimmer, the shock will go into your pump and then back out of your swimming pool return jets.

Also Know, should you run your filter when you shock your pool?

It's best to run the pool filter for 6-8 hour before shock treatment, and to schedule the shock when the sun has set. Performing pool shock treatment will lower the potency of chlorine, making you use either twice as much chemical, or render your shock treatment ineffective.

What setting should pool filter be on when vacuuming?

For routine vacuuming, the filter valve is left in the normal “Filter” position. This directs dirty vacuum water through the pool filter to remove the contaminants, then conveys filtered water through return lines back to the pool. The "Filter" setting is used for light to moderate levels of pool sediment.

36 Related Question Answers Found

What setting should pool filter be on?

Filter. The lever should be on the 'Filter' setting most of the time. This is the setting that provides normal pool filtration by pushing the water through the filter media (sand, glass beads or D.E) that then traps any dirt and debris before the water is returned to the pool.

How long does it take for a pool to clear up after you shock it?

Chlorine- free shock oxidizes bacteria and organics in your pool without any additional chemicals. With this type of shock, you can swim in the pool just one hour after. Chlorine- based shock contains high levels of pH and will alter both your pH and chlorine levels in the pool.

How long can you run a pool pump on recirculate?

They instructed me to set the valve on recirculate and add flock to the water and run for 2 hours.

Do you vacuum a pool on backwash or waste?

To begin vacuuming your pool:

If you do have this option, it is highly recommended that whenever you have algae, you will need to vacuum to waste. This option allows you to vacuum the algae up and send it out through the backwash line, avoiding getting algae into your filter sand.

How often should you backwash a sand filter?

As a rule of thumb, you should backwash and rinse your filter about once a week. The optimal time is right after you vacuum the pool. However, if your pool has had a lot more use than normal, it may be necessary to backwash twice a week.

Do you run pool pump while swimming?

Although it's generally recommended that all the pool water undergo filtration every 24 hours, the pump does not need to run all the time. If your pool is in constant use, you may need to run the pump for up to eight hours per day, frequently checking the water clarity and chemical balance.

How do you bypass a pool filter?

Bypass your filter so algae doesn't flow back into your pool with vacuum to waste.

Turn off the pump.
Move the multiport valve to the waste setting.
Turn the pump back on.
Close all skimmer lines except for one.
Close your main drain down to 50%
Set up your vacuum the way you normally would for regular vacuuming.

Can you shock a pool too much?

If you put too much shock in the pool, simply wait it out. If you have a cover on your pool, take it off. The more sun that hits your water, the faster it will dissipate. Technically, if your free chlorine levels are holding up swimming UP TO your shock level, depending on your CYA, is safe.

Can you put shock and chlorine in a pool at the same time?

You do need to use both tabs and shock. Without tabs, the chlorine shock will dissipate quickly out of the water; without shock, the chlorine level will not get high enough to fully sanitize the water. You should aim to keep the chlorine level at between 1 and 3 ppm.

Should I backwash after shocking pool?

If your pool is very dirty, it may need MANY pounds of Granular Shock over a period of days before the water clears. Green or cloudy water will quickly clog a filter, therefore you may have to backwash your filter many times a day until the pool clears. THIS IS NORMAL ! Remember, you cannot over-backwash a pool filter.

Is it better to run a pool pump at night or day?

Is It Better To Run Your Pool Pump At Night Or During The Day? Running the pump at night should only be when you are doing a major chemical treatment such as algae clean-up. Your pool is more vulnerable during the day, plants don't grow at night the way they do during the day–that's true of ALL plants including Algae.

How often should you shock a pool?

Always make sure that the filter system is running while shocking the pool. Some pool owners choose to shock their pools once every 1-2 weeks as normal maintenance. This is a great way to keep your chlorine level up and prevent algae growth.

Is it OK to run pool pump 24 hours a day?

there should be no reason you HAVE to run 24 hours. if you have a variable speed pump on low, then running 24 hours is no big deal because its not costing much. running a single speed pump all day is gonna get expensive.

Why did my pool turn green after I shocked it?

Cause. Shocking a pool should help clear up a green pool if the water is green because of algae or other issues. However, the pool may turn green after shocking, which is caused by an increased amount of dissolved copper in the water.

How many hours a day should a pool pump run?

8 hours

How much bleach do you use to shock a well?

Mix 2 quarts bleach in 10 gallons of water; pour into well. Connect a garden hose to a nearby faucet and wash down the inside of the well. Open each faucet and let the water run until a strong chlorine odor is detected, then turn it off and go to the next one. Don't forget outdoor faucets and hydrants.

How do you shock a pool with bleach?

Calculate the amount of bleach you need based on the fact that 1 gallon will raise the free chlorine level of 30,000 gallons of water by 2 ppm. If you need to mildly shock a 30,000-gallon pool by raising the free chlorine concentration to 5 ppm, you need 2.5 gallons of bleach. To raise it to 10 ppm, you need 5 gallons.