What does yellow triangle mean on DSC alarm?

trouble light

Consequently, what does triangle mean on alarm?

The yellow triangle means that your alarm system is experiencing a trouble condition. This could be caused by a number of different possible factors, such as a low battery, an activated tamper or communication problems. Only certain alarm systems use a yellow triangle to indicate a trouble.

One may also ask, how do you troubleshoot a DSC alarm system? How to Troubleshoot Problems on the DSC Home Security System

Press the pound key (#) to stop the security system from repeatedly beeping.
Press the star key (*) and then press the number 2 key.
Change the battery per the panel's instruction manual if a number 1 appears on the display or the 1 zone is illuminated.

Correspondingly, how do you clear the yellow light on a DSC alarm?

Press the '7' key and you will receive a number corresponding to the affected zone. The indicated zone is reading a low battery condition and needs a replacement battery. Replace the battery in the contact and the condition will clear.

Why is my DSC alarm beeping?

Battery Trouble If your DSC home alarm is beeping due to this condition, the main panel battery is low or failing. If you've recently had a power outage, wait 24-48 hours after power is restored. The battery can be replaced by your alarm company, if you have one.

30 Related Question Answers Found

How do I stop my ADT alarm from beeping with low battery?

Most systems will begin beeping or chirping as a result of a total power outage or failure to recharge the system backup battery. For many of our most popular systems, beeping alarms and low battery trouble beeps can be silenced by pressing the [OFF] or [#] buttons from the keypad.

What does 103 Comm trouble mean?

The message "103 check lngrng radio" on your ADT System means that there is a problem with the system's backup communicator. The Check 103 Error message indicates that there is something wrong with the system's communicator. The message can only appear on Alphanumeric Keypads.

Why does my ADT Alarm say trouble?

A trouble signal (sometimes indicated in the alarm history by the abbreviation TR) indicates a possible problem or difficulty with your security system, such as a loose wire, a poorly aligned sensor or a low battery status.

How do I reset my DSC alarm?

How to Reset a DSC Alarm After the Power Has Been Off

Open the access door on the unit.
Press and hold the "RESET" key for 2 seconds.
Press the buttons "*72" if the alarm does not reset after pressing the RESET button.
Check the sensors if it still does not turn off.

Where is the reset button on my ADT keypad?

Step 1: Locate the reset button on your ADT alarm keypad. Press down the reset button and hold it down for about two seconds.

How do you silence a DSC alarm?

Press * and then the 6 button on the keypad.
Enter your master Code.
Use the < and > keys to scroll to “Buzzer Control”
Press *
Use the < and > keys to scroll through the various buzzer settings, and adjust to your preference. “0” will silence the DSC keypad.
Press # to exit.

How do I get my DSC keyboard to stop beeping?

Tech Tips: Silence DSC Maxsys 4020 Keypad from Beeping on a Trouble

Hold down the * button until desired volume or silence.
Release the button once the desired volume or silence is found.
A message will be displayed on the keypad asking to press “1″ for bypass zones.

How do I reset my home alarm?

How to Reset a Home Alarm System

Check the manufacturer's website for installer instructions.
Check out do-it-yourself alarm support sites (see References below).
Locate the power source to the Main Control Panel.
Disconnect the backup battery in the Main Control Panel.
Leave power off for a minimum of five minutes.
Reconnect the battery leads.

How do I set the date and time on my DSC keypad?

How To Change the Time and Date on the DSC Power Series Neo Keypad

Press the * button, followed by 6.
Enter your system's master code.
Press 1 to Select Time and Date programming.
If you have a Full Message LCD Keypad, use the < or > keys to scroll to the menu options and press *.

How do I change the battery in my DSC keypad?

How to Change Batteries in a DSC Alarm System

Check the display panel on the keypad.
Remove the keypad from the mounting bracket by sliding it up and out.
Turn the keypad over, The battery bay contains four AA-batteries.
Slide or screw the keypad back in place.
Open the front cover by pressing down on the tab.

How do I deactivate my alarm system?

You can turn off or power down your home alarm system by disconnecting its backup battery and then unplugging the transformer for the device from the wall outlet. You can confirm that the panel has been powered down by checking its touchscreen or keypad and making sure that it is blank.

How do I stop my house alarm from beeping with low battery?

If faulty or dead batteries are not the cause, try to silence your alarm.

Most standard systems will allow you to stop the beeping using one of the following methods:

Disarm your system by entering your unique code.
Arm your system and immediately disarm.
Press the status button on your keypad.

How do I get my alarm to stop beeping when power goes out?

AC Power failure – if your alarm/keypad is beeping due to the loss of power you can silence the beeping as follows:

If you have a Command button, press Command 4.
If you have a Clear button, press Clear.
If you do not have a command or clear button, you can enter your digital code (make sure this doesn't arm your system)

Where is the battery on DSC alarm?

This is done by opening the panel box, which you will do anyway to locate the battery inside. Once the power is off, find the battery, which is a big box that looks like a mini car battery. Position the battery on its side so that you can access the terminals on its top.

How do you program a DSC alarm zone?

To program your zone definitions, you must: Enter Programming by pressing " * 8 + Installer Code " Enter Section 001 (Section 001 is used for Zones 1 - 16 only If you have more than 16 zones, you will use 001 for the first 16 zones, then you will use section 002 for zones 17-32)

How long does a DSC alarm battery last?

about three to four years

How do I reset my home alarm after changing the battery?

Press the "Home" or "Away" button to arm the system, then immediately enter your access code and press "Off." This action will reset the alarm to illuminate the low-battery signal to the system. The "Low Bat" indicator will go off, and the sensor number will be erased on the keypad of the master console.