How do you wire a Rain Bird?

Twist one of the two black wires coming from the top of the valve around the white wire and twist the other around the stripped colored wire. Slide each wire pair into a waterproof wire nut and turn the nuts clockwise while pushing toward the wire to tighten the nut.

Accordingly, how do you wire a Rain Bird solenoid?

Wiring the solenoid correctly ensures the correct valve is activated when turned on by the controller.

Unplug the Rain Bird control box so there is no power going to the valve wires.
Open the control box to access the wiring panel.
Screw the replacement solenoid clockwise into the threads on top of the valve.

Beside above, does sprinkler wire need conduit? Sprinkler wire is a vital part of an underground system. Conduit is pipe meant for electrical wires and cables. It's usually cheaper than sprinkler pipe because it doesn't need to withstand internal water pressure.

Also Know, how does a Rain Bird valve work?

All systems are limited by a combination of the pressure of the wa- ter (psi) and the number of gallons per minute (gpm) available. Each sprinkler uses a certain num- ber of gallons per minute of water. This release of water through the nozzle reduces water pressure to a certain degree while the system is working.

What is a master valve on a sprinkler system?

A master valve is an automatic valve, typically an electric solenoid type valve, that is installed at the point where the irrigation system connects to the water supply. The master valve is wired to a special "master valve circuit" on the irrigation controller. (Sometimes this circuit is called a "pump start circuit".

39 Related Question Answers Found

How deep are sprinkler lines?

Basic Depth Requirements

In most areas, burying the pipes 8 to 12 inches below the surface is adequate. This measurement is from the top of the pipe to the surface of the soil, which means your trenches must be slightly deeper to accommodate the pipes.

What kind of wire is used for sprinklers?

Most residential sprinkler systems can use 18-gauge electrical wire.

How do you install a sprinkler system yourself?

plot types and locations of sprinkler heads. Plan the System.
install an anti siphon valve. Access the Water Line.
dig the trench for system.
attach one end of valve manifold assembly to water.
attach risers using 90 degree connectors.
level sprinkler heads with soil level.
timer controls length and frequency of waterings.

How many zones do I need for my sprinkler system?

The resulting number will equal how many zones you need. If, for example, each sprinkler head will require a flow rate of 1.31 GPM and you have 20 of them, then you will need 26.2 GPM total. If your system can only handle 16.67, you will need to use two zones to cover that same area of your yard.

Does each sprinkler zone have a valve?

An irrigation system is typically divided into several zones, each of which feeds sprinkler heads in a different area of the lawn or garden, and each zone is controlled by a valve that receives signals from a centrally located controller. Often the valves are located inside one or more in-ground valve boxes.

How do I bleed my sprinkler system?

How to Bleed a Sprinkler System

Locate and turn off the main water valve for your sprinkler system by turning the valve in the clockwise direction until it is fully closed.
Locate the sprinkler head.
Detach the sprinkler head from the main water line.
Drain the main valve into a bucket by turning it clockwise with a socket wrench.

What causes a sprinkler valve to stay open?

Air Trapped in the Valve:

A small bubble of air becomes trapped in the tiny water ports of the valve, this stops the water from flowing through the port. Since the water flowing through the port is what holds the valve diaphragm closed, the valve stays open.

What does a solenoid do in an irrigation system?

Solenoid valve for irrigation. A water irrigation solenoid valve is an electrically controlled valve to regulate the flow of water. By applying a voltage over the coil, the valve opens and the liquid can flow through. Solenoid valves are also called electromagnetic valve, water valve, electric valve or electro valve.

How do you wire a solenoid?

How to Wire a Solenoid Switch

Locate the high-current switch terminals on the solenoid switch.
Cut two pieces of black wire and strip half an inch of wire off of each end of both wires.
Connect one end of the second black wire to the second high-current terminal of the solenoid switch.

Should sprinkler valves be open or closed?

Make sure the sprinkler valve is closed, unless it's the valve farthest from the main water source. You'll want to leave this valve open and remove the sprinkler nozzle to allow air to escape when you turn on the water.

What causes low water pressure in one station of a sprinkler system?

Low water pressure in your sprinkler system cuts down the irrigation range and can even cause the sprinkler heads not to pop up at all. Here are some of the most common culprits: The valves on the backflow preventer device aren't all the way open. The sprinkler heads are dirty or clogged.

How do you wire an anti siphon valve?

Many anti siphon valves come with a sprinkler head attached; however, if yours does not, you will need to install one. To do this, use a three-inch piece of PVC pipe. Use the PVC primer on the female connectors and both ends of the pipe. Then, secure the pipe to the valve and the sprinkler head with PVC glue.

Why does my Rain Bird Sprinkler System keep running?

A common reason why a program is repeating is that you have a second start time set. The start times control the exact time your ESP-Me timer will begin to water and they also control how many times a day your timer will water. The ESP-Me allows you to set up to 6 start times per program.

What is a Rain Bird irrigation system?

The first professional grade Rain Bird sprinkler system designed for homeowner installation, it provides everything you need to keep your lawn green season after season while saving water. Simple adjustments for spray rotation and distance help you keep the water on your lawn and off the house, sidewalk and driveway.

Why is my sprinkler valve box full of water?

If your valve box is full of water, does it mean your lawn sprinkler system is leaking? It might! Perhaps, it's just been rainy, and your sprinkler valve box is retaining water due to our clay soils. Or maybe, there's a leak upstream that's trickling into the box.

How do you manually run a sprinkler system?

Pro-C - Manually Run a Single Station

Turn the dial to the MANUAL position.
Station run time will flash in the display. Use the button to move to the desired station.
Turn the dial to the RUN position to run the station (only the designated station will water, then controller will return to automatic mode with no change in the previously set program).

How do you winterize a sprinkler system for a Rainbird?

How Do I "Winterize" My Irrigation System

Insulate your assets: Shut off the water supply to the irrigation system.
Stay in control: If you have an automatic system then you will need to "shut down" the controller (timer).
Drain the pipes:
Protect valves and backflow preventers: