How do you hang a shop light from the ceiling?

Mark spots on the ceiling for the two eye bolts that will support the chains for the shop light.
Drill holes through the railings in the spots you marked with a drill bit slightly smaller than your eye bolts.
Screw eye bolts into the drilled holes then tighten them up with a wrench until they are snug.

Also know, can LED shop lights be flush mounted?

Most LED shop lights include a chain that allows the fixture to hang from the ceiling. Some will also allow for flush mounting directly onto the ceiling. Some LED shop lights will include reflectors on the side of the fixture, to help direct the light downwards.

Additionally, how many LED shop lights can you connect together? Along with a five-foot power cord, the Commercial Electric LED shop lights come with a 13” linking cord and an end-to-end connector, allowing you to chain up to nine of the lights together.

Secondly, how many lumens is a 30x40 shop?

30X40=1200sqft X 100 Lu = 120000 /2600 = 46 T8 32W tubes or 12 4 tube fixtures. 2600 lumens per 32W T8 tube is about average.

How do you add more lights to a circuit?

Adding a Light Fixture Mid-Circuit You can usually install a light fixture between an existing one and the switch by cutting the cable to the existing fixture at the location of the new one, inserting the ends of the cable into the electrical box for the new fixture and pigtailing the new fixture onto these wires.

35 Related Question Answers Found

Can you hardwire a LED Shop light?

Re: Hardwire LED Shop lights? Theoretically you could add an outlet to an existing light - some lights come this way already. However if the light doesn't have a built in fuse or breaker, you would want the entire light to be wired with 14 gauge wire.

How do you wire a LED light plug?

Plug in the adapter to power the strip.

Once the wires are securely attached to the adapter, plug in a power supply cord into an outlet. Then, plug the power cord into the slot on the adapter. The lights on the strip will turn on. Cover the LED strip with a plastic or aluminum casing to keep them protected.

What is the best shop lighting?

The FrenchMay linkable 4ft LED Utility is the best shop light that will light up your garage in the most efficient and cost-effective way. The light will give you brighter, healthier and cheaper lighting than any other fluorescent light. The light is long-lasting and durable as it lasts up to more than 20 years.

How do you wire a light?

Wrap the copper or silver ground wires from the light fixture around the ground screw. Then, connect it to the supply ground wire of the junction box with a wire connector. Connect the black or red current wires and the white neutral wires. Then, push the connected wires into the junction box.

What wire do you use for shop lights?

As long as you don't put too many lights on the light circuit, you can usually control that circuit with a 15-amp breaker, as well as wire it with a 14-gauge wire. On the other hand, an outlet circuit controlled by a 20-amp breaker requires a 12-gauge wire.

Can you convert a hardwired light to a plug in?

It's that easy to turn a hardwired light fixture into a lamp that can be used in any dry, safe spot that an extension cord can reach! You can even use a Wireless Wall Switch to turn the plugged-in lamp on and off from a doorway or nightstand.

What is a linkable led shop light?

LED Linkable Shop Light is designed to replace traditional outdated fluorescent fixtures, typically used in garages, basements and work shops. It emits 3200 Lumens of cool to the touch 4000K Bright White light using only 35-Watts of energy.

Can you convert a light to an outlet?

Converting a ceiling light to a receptacle is a convenient and inexpensive way to provide an outlet for ceiling-mounted devices. This conversion is possible because most ceiling light fixtures operate using the same voltage required by a typical wall outlet.

How do you wire a 3 prong plug?

How to Wire a Three-Pronged Plug to a Hard-Wired Appliance

Shut off the power to the appliance at the breaker panel.
Open the junction box containing the spliced connection to the house wiring.
Remove the wire nuts over the spliced connections on the black and white wires.
Strip off 1/2 inch of the insulation from the black and white wires with wire cutters.

Are light sockets grounded?

The grounding wire ensures that no stray electricity leaves the wire and enters metal parts of the lamp, which can cause physical injury if someone touches it. Lamp sockets that are grounded use three-wire cords and a three-pronged electrical plug.

Can you put LED bulbs in shop lights?

In short, YES!

New linear LED tube bulbs are simple plug and play and ballast compatible. You will simply need to remove your fluorescent bulb and plug in your LED replacement. Read on for more info to support your decision to replace your linear fluorescent light bulbs with tube LEDs.

How many lumens do you need to light a shop?

A general rule of thumb is to use 130 to 150 lumens per square foot of work space. For example, a 40-watt fluorescent bulb puts out about 2,200 lumens. A 60-watt incandescent bulb puts out about 800 lumens.

How many amps does a 4 foot LED light draw?

The Feit 4' LED shop lights draw about 0.3amps each according to the manufacturer. 6 times . 3 amps is only 1.8 amps, round up to 2. You are obviously well within the capacity of a 20 amp breaker.

Are led shop lights dimmable?

While most LED bulbs are now dimmable, not all of them are and not all of them dim in the same manner Since LEDs consume such a low wattage, many types of dimmers do not function with LED in the same way that they do with high wattage load incandescents.

Are led shop lights better than fluorescent?

LED Shop Lights do not break easily unlike fluorescent lights. They are also much lighter and brighter than fluorescent lights. These lights are also very reliable and last for up to 50,000 hours. The LED Lights in this video were about $40 for 2 which is more than the typical fluorescent lights.

What are the brightest LED shop lights?

Top 8 Best LED Shop Lights 2020 Reviews

Kihung 8FT LED Shop Lights for Garage, V Shape T8 Integrated Tube Light Fixture.
Monios-L 4 Foot LED Shop Light, 48W 5000LM 5000K Daylight White, LED Wraparound Light Fixture 4ft.
Onlylux LED T5 Integrated Single Fixture, 4FT, 18W, 2000lm, 6500K(High Brightness Output)
Kihung 4FT LED 6500K (Super Bright White)

Do LED lights have ballasts?

No LED bulbs require a ballast, although some are engineered to work with an existing ballast. You will find ballast-compatible, or "plug-and-play" LEDs that are designed to replace linear fluorescents, compact fluorescents, or HIDs. Fluorescent lamps and HID (high intensity discharge) light bulbs do require a ballast.