Are circular saw blades the same as table saw blades?

Category: hobbies and interests woodworking
4.5/5 (264 Views . 12 Votes)
Using Circular Saw Blades in Your Table Saw. Many new woodworkers do not know that the arbor in a circular saw is the same diameter as most 10" table saws which means the blades for circular saw fit nicely onto most 10" table saws.



Besides, can a circular saw blade be used on a table saw?

Circular saw blades are designed for use with miter saws, table saws, radial arm saws, cut-off saws and standard circular saws. Many circular blades can be used interchangeably between devices. This guide will help you use the correct blade for each job.

Secondly, what are the different types of table saw blades? There are four basic blade types, determined by the shape, or grind, of their teeth. They are flat top grind (FTG), alternate top bevel (ATB), combination (ATBR), and triple-chip grind (TCG) [Figure 1 and Photo A].

In this manner, are table saw blades interchangeable?

The short answer is yes you can, but that's a lot of teeth for a table saw blade. Why you want to use it on the table saw to cut hardwood? A good 40 tooth combo blade would be a better choice to get a smooth cut. I think a 72 tooth blade is going to cut very slowly and may burn the wood easily.

Why does my circular saw burn the wood?

A Dull or Dirty Saw Blade Might Be the Culprit Pushing the stock through the saw too slowly is a common cause of saw blade burn. Sometimes a blade that feels dull might only be dirty. If wood pitch resins build up behind the teeth of the blade, the cutting speed will slow down, increasing the chances for burns.

29 Related Question Answers Found

What type of circular saw blade should I use?

Blades with a thin kerf tend to be sharper and cut faster. Thinner kerf blades require less work from your motor since they cut less wood. If your saw doesn't pack a large amount of power, thinner kerf blades are the best choice. However, thin kerf blades tend to cut rougher edges than thicker kerf blades.

Can table saw blades be sharpened?

You can sharpen steel-toothed circular saw blades yourself using a file. Carbide-tipped blades need to be taken to a professional sharpening service for two reasons: Carbide is so hard that you need a diamond wheel sharpener for it, and sharpening carbide blades is so complicated that you can easily ruin the blade.

Can you put 2 blades on a table saw?

If you stack two regular blades , make sure the set of the teeth are alternating so the blades are not bent. The Dado blades are set up to fit stacked. Yeah that is the way I was going to do it

What is the best circular saw blade for wood?

Best Circular Saw Blades - Reviews
  • Freud D12100X 100 Tooth Circular Saw Blade. The Freud D12100X is a 12-inch saw blade with 100 teeth.
  • DEWALT DW3106P5 - 10 Inch Saw Blade.
  • Freud D1060X Diablo 10-Inch Finish Saw Blade.
  • DEWALT DW9196 6-1/2-Inch 40T Saw Blade.
  • SKIL 75312 7-1/4-Inch Saw Blade.

Are circular saw blades hardened?


Most modern circular saw blades have hardened teeth fused to a mild steel body which cannot be hardened.

How many teeth do I need on my circular saw blade?

The least number of teeth you will find on a circular saw blade is about 14. A circular saw blade is only 7-1/4 inches in diameter. Fourteen teeth are ideal for the rough cuts on 2x4 framing lumber, and they cut very fast.

Is more teeth on a saw blade better?

Blades with more teeth yield a smoother cut. Blades with fewer teeth remove material faster, but tend to produce a rougher cut with more “tearout”. More teeth means you will need to use a slower feed rate. No matter what type of saw blade you use, you will likely wind up with residue on the saw blade.

Which table saw blade is best?

10 Best Table Saw Blades Reviews (2020)
  • Freud 40-Tooth General Purpose.
  • Freud 80-Tooth Ultimate.
  • DEWALT Series 20 10-Inch.
  • Overpeak 80-Tooth ATB.
  • HICO 40-Tooth ATB. Popular Features.
  • Overpeak for Hard and Soft Woods. Popular Features.
  • IRWIN Tools Classic Series Steel. Popular Features.
  • INGTERCO 80-Tooth ATB. Popular Features.

Can you use a 7 inch blade on a 10 inch saw?

A smaller saw blade may reduce kickback injuries, says Bob Chase. At Chase Cabinets, owner Bob Chase makes the case is simple: Replacing the 10-inch blade on a table saw with a 7-1/4-inch blade can bring immediate benefits.

How long do saw blades last?


Some can last under six months, and some can last years! Some of the most important variables to consider are what you are cutting, the condition of the machine and blade, how long you are using the blade, and even how you are feeding the wood through your saw as well.

Are miter saw and table saw blades are interchangeable?

A: Yes, you can. However, since your miter-saw blade is thin-kerf, you might need to change the tablesaw's splitter. If the splitter is thicker than the blade, the workpiece will get caught on it and you'll be unable to feed it through.

Does MDF dull saw blades?

For particleboard or MDF, it is suggested to use a triple chip grind blade with 80 teeth. Man-made materials can quickly dull saw blades. With a triple chip grind, the corners of every other tooth are chamfered at 45°.

Can you use a crosscut blade to rip?

The Crosscut blade is used when cutting short grain, while the Ripping blade is for long grain. The Combination blade allows one to cut both crosscut and ripping using the same blade.

What saw blade for melamine?

Amana's carbide tipped melamine cutting saw blades provide incredibly smooth, chip-free cuts in melamine and laminates. The industrial quality #MB10800 double-face blades are specifically designed to cut melamine chip-free on both sides of the material.

What is a kerf blade?


The term "kerf" is used to describe the thickness of the cut a woodworking saw blade makes in a piece of wood as it cuts through it. The term is also sometimes used to describe the thickness of the blade itself; for example, you may see the packaging of a circular saw blade or table saw blade listing its kerf width.

What is the best blade to cut MDF?

Any circular saw or handheld cutting tool will make rip cuts or crosscuts in MDF, but the blade should be carbide-tipped, because the high glue content of the material dulls steel blades quickly.

Can you put a 12 blade on a 10 table saw?

Theoretically, a 10-inch blade will fit on a 12-inch saw, but the arbor -- or hole in the middle of the blade -- is typically smaller. Ten-inch blades can be ordered or bored out to fit a 12-inch saw, but it's expensive and usually not worth the effort.