Why is my KitchenAid ice maker not working?

If the icemaker module is defective, the ice maker won't make or dispense ice. First, depending on your model, make sure that the on/off switch is in the on position or the bail arm is in the down position. If the icemaker module has ejector blades, check to ensure that ice cubes are not stuck in the blades.

Also question is, how do I reset my KitchenAid ice maker?

Close the freezer door for 10 seconds, open it and press the door switch in and out three times. Close the freezer door immediately, wait between five and 50 seconds then open the freezer door again. If the light still blinks twice, the reset did not correct the issue.

Secondly, why is there no water going into my ice maker? Water may not be reaching the ice maker due to a frozen line, missing filter, or a closed supply valve. This is the water supply line. The valve is usually located under your kitchen sink, or there may be one behind the refrigerator. If there is no moisture on or around the valve, then there are no leaks.

Consequently, why did my ice maker stop working?

If your ice maker isn't producing ice at all or is producing crescents or cubes that are smaller than usual, it's typically indicative of a clog somewhere along the supply line. Cause: A common cause for a clog is frozen water in the line. Fix: To repair a frozen line, slide the refrigerator and unplug it.

How long does it take for a Kitchenaid ice maker to make ice?

6 to 12 hours

32 Related Question Answers Found

Will my ice maker work without a filter?

Operating Without a Filter

If the refrigerator does not have a bypass plug and the filter housing can be closed with the filter cap, a filter is not needed. If the refrigerator has a bypass plug, it must be properly installed for the water and ice dispensers to work without a filter.

How do you test an ice dispenser motor?

Push on the ice dispensing lever as you watch the auger motor at the back of the freezer. If the motor jumps slightly, but fails to turn, chances are the motor is frozen from moisture.

Why wont my ice maker fill with water?

If the water inlet valve is defective, or if it has insufficient pressure, it won't allow water to flow through. As a result, the ice maker won't make ice. If the water inlet valve has sufficient pressure and is getting power, but the ice maker won't fill with water to make ice, replace the water inlet valve.

Why is my Samsung ice maker not making ice?

If the ice maker appears to not be making any or enough ice, low water pressure or a faulty water filter may be to blame. When the ice maker makes small, cloudy, or clumped ice, it could be something as simple as a dirty water filter, low water pressure, or high mineral deposits in your water.

Why is my Samsung freezer not making ice?

If the water inlet valve is defective, or if it has insufficient pressure, it won't allow water to flow through. As a result, the ice maker won't make ice. If none of these parts are at fault, and the freezer temperature is at least 15 degrees Fahrenheit, replace the ice maker assembly.

How much is a Kitchenaid ice maker?

5. Remove the wiring harness from the old icemaker (you have to remove the front cover to access the white clip first).

Top Selected Products and Reviews.

List Price:	$158.72
Price:	$86.25
You Save:	$72.47 (46%)

How do you reset the ice maker on a Frigidaire refrigerator?

Some Frigidaire refrigerators have an an on/off button for the icemaker located on the front control panel. To reset the icemaker press this switch until the LED turns red, wait a few minutes, then press and hold it until the LED turns green.

How do I unfreeze my ice maker?

How to Defrost an Ice Maker

Unplug the refrigerator and remove any ice from the ice maker and the ice tray.
Locate the water refill tube that runs to the ice maker.
Turn a hair dryer on low speed and point it at the refill tube to defrost.
Replace the metal clip and the ice tray before plugging in the refrigerator.
Things You Will Need.
Warnings.

How much does ice maker repair cost?

A typical ice maker costs between $60 and $200 to replace, Daganaar says. Some of the factors that affect price include accessibility of the components and the brand.

How long does it take an ice maker to cycle?

Normally an icemaker that is inside a freezer that doesn't drop below 0°F, (as recommended by the manufacturers), with water no warmer than 70°F will cycle about every 90 minutes. It takes about two and a half minutes for the cycle to complete.

How do I know if my ice maker is bad?

If the ice maker makes cubes and kicks them into the bucket – the water inlet valve is bad. If there are no new cubes in the bucket – the ice maker is bad.

Where is the reset button on a Kitchenaid ice maker?

To access it, you must first remove the ice tray. Once you do that, you should see the bright red reset button on the bottom of the ice maker itself. To reset the ice maker, push this button in and hold it for 10 seconds.

How do I reset my Kitchenaid ice maker?

Why would an ice maker stop working?

If your ice maker isn't producing ice at all or is producing crescents or cubes that are smaller than usual, it's typically indicative of a clog somewhere along the supply line. Cause: A common cause for a clog is frozen water in the line. Fix: To repair a frozen line, slide the refrigerator and unplug it.

How long before ice maker fills with water?

To be safe, it is best to wait at least 24 hours. If the icemaker was installed but the water line was not added until later, once the water and icemaker is turned on the icemaker will cycle within a few minutes and fill and process its first cubes in about 1 1/2 hrs.