What's the difference between first fix and second fix nail guns?

Asked By: Nadene Babahanov | Last Updated: 18th February, 2020
Category: style and fashion nail care
4.5/5 (403 Views . 17 Votes)
The key difference between first fix and second fix nail guns is that first fix nail guns are more powerful machines that use larger nails for heavy duty framing applications. Second fix nail guns are used for the more delicate finishing work on site, such as door frames, skirting, furniture and more.

Click to see full answer


Subsequently, one may also ask, what is the difference between 1st fix and 2nd fix?

These terms are used throughout the industry and is commonly referred to the carpentry work on a building. First Fix involves the structural work (roof struts, wall studding, framing and joists etc) and Second Fix refers to the finishing work, which is usually done after the plastering.

Subsequently, question is, what is the best first fix nail gun? DeWalt DCN692P2-GB 90mm 18V 5.0Ah Li-Ion XR Brushless First Fix Cordless Nail Gun (4477D)

  • 2 x 5.0Ah Li-Ion Batteries.
  • 90min Charge Time.
  • Fires 18ga 50-90mm Nails.

Also Know, what is a second fix nail gun used for?

Second fix nailers are used to complete 'softer' jobs; they use smaller nails to reduce any potential impressions or damage to the work area. That's the reason that these nail guns are ideal for more delicate interior work such as door frames, general woodwork finishing and household mouldings.

What's the difference between nail guns?

The primary difference between a brad nailer vs finish nailer is that the brad nail gun shoots 18-gauge nails whereas 16-gauge or 15-gauge nails are used in the finish nailer. On the other hand, a finishing nailer is what you will use for most of the carpentry and woodworking jobs though you may need to putty the hole.

38 Related Question Answers Found

How long does 2nd Fix take?

Your second fix does seem a bit slow, how long does it take you to do the CU on average? About 5 minutes per accessory is probably about right plus a couple hours for the testing of everything. So perhaps 1/2 hour per room on average unless it has loads of sockets, or AV etc.

What is 2nd fix electrics?

Second fix comprises all the work after the plastering of a finished house. Electrical fixtures are connected to the cables, sinks and baths connected to the pipes, and doors fitted into doorframes. Second fix work requires a neater finish than first fix.

What is included in 2nd fix carpentry?

Second Fix Carpentry
This involves fitting floor boards and architraves, doors and windows in to frames, connecting up pipes to baths and sinks, and fitting electrical fixtures and connecting them to cables.

What is 3rd fix carpentry?

It consists of item you touch on a daily basis, the finishing touches and forms the way you interact with your home. Third fix carpentry, as I call it, is where I come in. Doors and windows are often the most used woodwork in a house; save for the stairs and floors.

What is a 2nd fix carpenter?


This includes carpentry work from constructing walls, floors and ceilings. Second fix comprises of all the neater work after the plastering to get the house finished. This includes things like fitting doors, skirting boards, architrave, kitchens and other finished carpentry work throughout the house.

Are stairs first fix?

Generally first fix will include constructing the structure, cladding, flooring, doorframes, stairs and so on and installing cables for electrical and ICT distribution, pipework for water and gas distribution and heating ventilating and air-conditioning (HVAC) distribution.

How do you repair electrics first?

First-Fix Electrics
This takes place prior to the insulation and plasterboarding being fitted. The wires are then left sticking out of the walls and ceiling. They are not connected at either end but left sticking out of the walls at one end and rolled up next to the existing fuse board at the other.

What is the best nail gun to buy?

View the Best Nail Gun on the Market, Below.
  • WEN 61720 18-Gauge.
  • DEWALT DWFP12231.
  • NuMax S2-118G2.
  • PORTER-CABLE PCC790LA Cordless Nailer Kit. CLICK HERE FOR PRICE.
  • Freeman PFR2190 Framing Nailer. CLICK HERE FOR PRICE.
  • Makita AF505N. CLICK HERE FOR PRICE.
  • NuMax SFN64. CLICK HERE FOR PRICE.
  • Stanley TRE650Z. CLICK HERE FOR PRICE.

Are Paslode nailers any good?

The Paslode cordless brad nailer performed just as expected, excellent. The fuel cell system produces very little recoil, especially for being so powerful. The battery is supposed to drive 10,000-12,000 nails per charge, while each fuel cell is rated to drive 1000-1200 nails per charge.

Do you need a license for a nail gun?


No license is required for blank cartidges either, but you might want to find somewhere local selling them - look for a gun shop maybe and take some Hilti's along to see if they have, or can get, anything similar.

What is the best nail gun for fencing?

5 Best Nail Guns for Fencing – Reviews 2020
  1. Freeman PFR2190 Pneumatic Framing Nail Gun – Top Pick. Check Latest Price on Amazon.
  2. Hitachi NR90AES1 Fencing Nailer – The Runner-Up. Check Latest Price on Amazon.
  3. NuMax SFR2190 – Best Fencing Nailer for the Money.
  4. BOSTITCH F21PL Framing Nail Gun.
  5. Valu-Air CN55R Fencing Nailer.

What is framing nailer used for?

A framing nailer is often used to handle large wood works or projects. This could mean building decks, framing houses or constructing a room. This type of nail gun is used for framing, wood siding, fence building, wood sheathing and major carpentry work. This is often the heaviest duty nailer.

How strong are Brad Nails?

Most brad nails are made from a very thin 18-gauge wire. Finishing nails typically range from 16 to 10-gauges and are much more robust than brad nails.

What is an angled nailer?

Angled Finish Nailer
The “angle” in its name instead refers to the magazine. Instead of running down from the part of the nailer that fires the nail into the wood at a 90-degree angle, it angles back towards your hand, which makes it shorter and more versatile.

What's the difference between straight and angled nail guns?


A straight nailer is shaped like an L, with the nail chamber extending from the gun and staying parallel to the ground. On the other hand, an angled nailer has a nail chamber that comes up at an angle. It's important to remember that the angle doesn't affect the angle that the nail is going to enter the wood.

What nail gun do I need?

The finishing nailer is your best all-around nailer for indoor trim and similar jobs. This uses shorter, lighter gauge nails, usually 14 to 16 gauge, 1” to 2½” nails. This is used for mouldings around windows and doors, baseboards, chair rails and such, as well as cabinet making.

What degree nail gun is best for framing?

Top 3 Best Framing Nailer
Framing Nailer Power Source Editor's Rating
Hitachi NR90AES1 Framing Nailer, 2-Inch to 3-1/2-Inch Plastic Collated Full Head Nails Pneumatic (4.6 / 5)
NuMax SFR2190 21 Degree Framing Nailer Ergonomic & Lightweight Pneumatic Pneumatic (4.4 / 5)