How much does a ton of slag cost?

Steel slag costs $25 to $39 per ton or $35 to $54 per yard, depending on the quantity ordered and size of stones.

Herein, how much is a ton of slag?

Steel slag costs $25 to $39 per ton or $35 to $54 per yard, depending on the quantity ordered and size of stones.

One may also ask, how much does a ton of 57 stone cost? #57 Granite Gravel---$52 per ton Typical construction, driveway, and drainage gravel.

Similarly one may ask, how much does crush and run cost per ton?

Crush & Run Cost per cubic yard is about $20 and per ton about $28. This material-also known as crusher run, quarry process, dense grade aggregate or road stone-is the combination of crushed rock and dust created in the process. Pros: Inexpensive.

Is slag good for driveways?

Steel slag is commonly used to cover driveways, to fill potholes, repair farm lanes, residential entrances, or yards. Steel slag is not just good for driveways, it is also used by homeowners as a landscaping stone in back yards around a pool area or patio.

39 Related Question Answers Found

How many tons does a dump truck hold?

Transfer dump trucks typically haul between 26 and 27 short tons (23.6 and 24.5 t; 23.2 and 24.1 long tons) of aggregate per load, each truck is capable of 3–5 loads per day, generally speaking.

How many tons are in a yard?

1.5 tons

How much gravel is in a dump truck?

When it comes to gravel, an ideal average is about 3,000 lbs per yard. A dump truck (pickup truck sized) can carry 1 yard and three-axle dump truck can carry about 16.5 yards of gravel.

How much will a ton of gravel cover?

Using 2 inches for the depth, the following measurements are a guide to the amount of gravel coverage per ton: 1/4 to 1/2 inch gravel, 100 square feet per ton; 1/2 to 1 inch gravel, 90 square feet per ton; and 1 1/2 to 2 inches gravel, 80 square feet per ton.

How many tons of gravel do I need?

Length in feet x Width in feet x Depth in feet (inches divided by 12). Take the total and divide by 21.6 (the amount of cubic feet in a ton). The final figure will be the estimated amount of tons required.

What is the best gravel for a driveway?

Top layer choices for gravel driveways might include crushed shale, limestone, granite and concrete, along with other types of gravel in various colors to meet your aesthetic needs.

How do you make a cheap driveway?

Cheap Ways to Pave a Driveway

Rustic Gravel. Gravel is one of the most inexpensive paving options for a driveway.
Durable Apshalt. Asphalt is usually quite affordable.
Elegant Tar and Chip. A tar and chip driveway is an affordable driveway paving option that often has a more decorative appearance than plain asphalt.
Low-Maintenance Concrete.

What is Type 2 gravel?

A graded aggregate, typically crushed stone and/or crushed concrete with sand and gravel. Used as granular sub base or back-fill. Type II compacts well. Type II quantity. Category: Sands, Soils, and Gravel.

Will crushed concrete harden?

Crushed Concrete: A fantastic driveway stone, hardens and compacts over time. Easy to install and long lasting. The product is run through magnets to remove most of the non-cement pieces from the recycling process. A few pieces of metal can sometimes be found.

How do I calculate how much crushed stone I need?

In the construction world, most materials are measured in cubic yards. Multiply the length (L), in feet, by the width (W), in feet, by the height (H), in feet, and divide by 27. This will tell you how many cubic yards of crushed stone you need. When using this equation, make sure all of your measurements are in feet.

What is crusher run gravel?

Crusher Run stone is a quarried material that is crushed to particular sizes. It has the fines, or dirt, left in it which causes the stones to bind together which makes it the perfect driveway gravel.

What size gravel do I need for my driveway?

In general, driveway gravel should be relatively large, between about 3/8 and 3/4 inch in diameter, as compared to the gravel used for footpaths, which is typically 1/4 to 3/8 inch in diameter. Another factor to consider is the amount of very small granular material, called "fines," in the gravel.

What does crusher run gravel look like?

Crusher run, with its angular facets, allows greater interlocking and stability than smooth rocks. Crusher run is a type of gravel that consists of angular, crushed rock ranging in size from 3/4-inch to silt.

How many square feet will a ton of crush and run cover?

135-123 square feet

How much is a ton of rock?

Landscaping Rock & Stone Pricing

Rock Type	Price
Large Boulders	$100-$600 per ton
Bull	$37 per cubic yard $4 per bag $2.50 per 5-gallon bucket
River Rock Gravel	$40 - $45 per ton $30 - $35 per cubic yard $4 - $8 per bag
Crushed Stone, Rock, Shells	$50 - $65 per ton $40 - $55 per cubic yard

How many yards are in a ton of gravel?

Converting Cubic Yards to Tons

For your reference, gravel typically weighs 2,800 pounds per cubic yard. In addition, there are 2,000 pounds to a ton. For instance, if your area to be landscaped is 100 cubic yards, multiply that by 1.4. You'll need 140 tons of gravel to cover this space.

Why is it called 57 stone?

#57. Crushed stone #57 refers to stone that is about ¾”. This is typically used for concrete mix, landscaping and drainage.