How do you sharpen a lead compass?

Asked By: Gerry Herforth | Last Updated: 7th January, 2020
Category: hobbies and interests drawing and sketching
4.5/5 (481 Views . 44 Votes)
The compass lead should be sharpened with a single elliptical face, as shown in figure 3-7, view A. A sandpaper pad works best for sharpening compass leads. The elliptical face of the lead is normally placed in the compass so that it faces outward from the other compass leg.

Click to see full answer


Furthermore, how do you use an engineering compass?

Use the engineer compass to measure the azimuth to take a bearing or direction. Open the engineer compass until the cover is 90 degrees to the compass case. Tilt the lens bracket approximately 30 degrees from the perpendicular position of the compass. Check that the dial is floating freely.

Likewise, how do you draw a circle with a protractor? Method 4 Using a Protractor

  1. Lay a protractor flat on a piece of paper. Position the protractor on the paper where you want to draw a circle.
  2. Trace the curved edge of the protractor. This will be the first half of your circle.
  3. Rotate the protractor and trace the other half of the circle.

Keeping this in view, why is a compass called a compass?

The word "compass" means "to go around, encircle"; it originally meant "to measure" by pacing (passus). Since a compass "goes around," this makes some sense. "

Which is attached to the compass for drawing large size circle?

A beam compass is used for drawing large diameter circles. The Alvin beam compass can draw a circle up to a diameter of 48 inches.

29 Related Question Answers Found

How do you construct a perpendicular bisector?

The perpendicular bisector of a line segment
  1. open the compass more than half of the distance between A and B, and scribe arcs of the same radius centered at A and B.
  2. Call the two points where these two arcs meet C and D. Draw the line between C and D.
  3. CD is the perpendicular bisector of the line segment AB.
  4. Proof.

How do you measure angles?

How to measure an angle with a protractor:
  1. Place the midpoint of the protractor on the VERTEX of the angle.
  2. Line up one side of the angle with the zero line of the protractor (where you see the number 0).
  3. Read the degrees where the other side crosses the number scale.

How do you draw a circle without a compass?

Don't like this video?
  1. Use you little finger as a pivot and rotate the apper underneath.
  2. Draw the circle using a paper clip.
  3. Tie the ends of 2 pencils using a rubber-band and draw it like a compass.
  4. Create an adjustable compass using 3 pencils.
  5. Use your index finger to mark the center of the circle and rotate the paper.

How does a drawing compass work?

A compass is an instrument used to draw circles or the parts of circles called arcs. It consists of two movable arms hinged together where one arm has a pointed end and the other arm holds a pencil. Note that a compass is also called a pair of compasses. tighten the hold for the pencil so it also does not slip.

What is the radius of a circle?


A radius is a straight line from the center of a circle to the circumference of a circle. If you have two or more of them, they are referred to as radii. All radii in a circle will be the same length.

What does a compass measure?

A compass is an instrument used for navigation and orientation that shows direction relative to the geographic cardinal directions (or points). Usually, a diagram called a compass rose shows the directions north, south, east, and west on the compass face as abbreviated initials.

What is the divider?

dividers, a pair of compasses, as used for dividing lines, measuring, etc. a partition between two areas or dividing one area into two, as a piece of cardboard in a box or a bookcase jutting out from a wall.

Which way is north?

Say it is two o'clock, draw an imaginary line between the hour hand and twelve o'clock to create the north-south line. You know the sun rises in the east and sets in the west so this will tell you which way is north and which way south. If you are in the Southern Hemisphere then it will be the other way round.

What does lensatic Compass mean?

Definition of lensatic compass. : a magnetic compass having a magnifying lens for reading the compass scale.

How do you know which direction is north?


- In the Northern Hemisphere:
  1. Point the hour hand (the little one) at the sun.
  2. Imagine there is a line down the middle of the angle between the hour hand and the 12 o clock mark.
  3. The line down the middle of the angle is pointing South; so the opposite direction is North.

What is an azimuth on a compass?

An azimuth compass (or azimuthal compass) is a nautical instrument used to measure the magnetic azimuth, the angle of the arc on the horizon between the direction of the sun or some other celestial object and the magnetic north.

Which direction am I facing right now?

Method 1. Stand with your right arm pointing to where the sun rises in the morning (East). Your shadow will face behind you when using this method. With your right arm facing East, you will then be facing North and be able to quickly know what direction North, South, East, and West is.

What is the use of compass divider?

A compass, also known as a pair of compasses, is a technical drawing instrument that can be used for inscribing circles or arcs. As dividers, they can also be used as tools to measure distances, in particular on maps. Compasses can be used for mathematics, drafting, navigation and other purposes.

What is the wire for on a compass?

The cover is used to protect the compass and also incorporates the sighting wire—which helps you determine direction. The base is the compass dial, bezel, and the thumb loop—the thumb loop is used for stability to garner a more accurate reading.

How do you use a field compass?


To use a compass, hold the compass flat on your outspread hand in front of your chest. Next, turn the degree dial so that the orienting arrow lines up with the magnetic arrow inside the compass. Then, look at the travel arrow on the baseplate of the compass to tell you which direction you're facing.

What is an engineer lensatic compass?

An engineer lensatic compass, also known as a hand compass or sighting compass, allows you to take bearings on physical landmarks which can then be used to determine your exact position on a map or navigate toward the landmark even when it can no longer be seen.