How do you nail a feather board fence?

Use 50mm galvanised nails to attach them - it is important you only use one nail per pale per rail (i.e. 3 nails) - do not nail two pales together. The single fixing is to allow the pales to expand and contract with the weather. As the top of the fence is continuous, capping can be any length.

Consequently, which way up does feather board go?

Skavenger. N.B. The Log Store is upside down so when it is the correct way up the fatter edge of the Feather is facing down.

Subsequently, question is, how do you calculate fencing? Equations used in the fence calculator Post length = fence height * 1.5. Total number of rails = number of rails per section * number of sections. Total number of pickets = fence length in inches / (picket width + picket spacing) (round the result up)

Hereof, how much do you overlap feather edge boards?

Feather-edge cladding is designed to be laid horizontally with a vertical overlap of approximately 40mm for boards up to 150mm, and 50mm for boards wider than 150mm. It is important to follow fixing advice, particularly when using green (wet) timber.

How much should close board fence overlap?

The overlap should be at least 25mm. Nails should be 50mm lost head nails or 50mm ovals. As you get towards the last post (between 6 to 10 boards distance) measure the distance and then adjust the spacing so that you finish at the outside edge of the post.

36 Related Question Answers Found

How many feather boards do I need?

As a guide Fencing Essentials recommend the following, when deciding how many boards are needed: Allow 12 boards per metre when using 100mm boards. Allow 10 boards per metre when using 125mm boards. Allow 8 boards per metre when using 150mm boards.

What's the difference between Closeboard and feather edge fencing?

Closeboard provides unparalleled privacy and is usually constructed using overlapping vertical feather edge board. Each board is nailed to horizontal rails, sometimes called 'arris' rails and these are supported by notched vertical posts. However, closeboard can be expensive when compared to other types of fencing.

What nails should I use for fencing?

The standard option is hot-dipped galvanized nails, which provide more corrosion-resistance than electro-galvanized or hot-galvanized materials. The most reliable material for pressure-treated wood is stainless steel. Use 6-d (2-inch) rink shank nails to fasten pickets and infill boards.

What is a cant rail?

The rails. Two types of rails are commonly found - arris rails with a triangular cross-section, and cant rails which are more or less rectangular with the top edge sawn at an angle to allow rainwater to run off away from the fence boards.

What nails do I use for feather edge fencing?

Use 50mm galvanised nails to attach them - it is important you only use one nail per pale per rail (i.e. 3 nails) - do not nail two pales together. The single fixing is to allow the pales to expand and contract with the weather. As the top of the fence is continuous, capping can be any length.

What are feather boards used for?

A featherboard is a safety device used when working with stationary routers or power saws such as table saws or bandsaws. The purpose of a featherboard is to apply pressure against a workpiece, keeping it flat against a machine table or fence.

How do you attach rails to fence posts?

Fasten the rail to the posts with #8 2½-inch deck screws. Cap rails: Cut rails so the joints fall at the center of the posts and the ends butt together tightly. Cut a 45-degree miter on rails that meet over corner posts. Fasten with 10d (3-inch) nails or #8 2 ½-inch deck screws.

How do you fit feather edge boards horizontally?

Horizontal attachment only

Begin at the bottom, ensuring that the first board is level. Use a 10mm strip behind the lower edge of the bottom board for support. Overlap subsequent boards by 40 – 50mm. It is important not to reduce the recommended overlap.

What are feather edge boards?

Each fencing feather edge board is cut from a 22x125mm board to give two boards that taper across the width. Don't forget to add a gravel board to finish of the bottom of the fence. All our feather edge boards are pressure treated to prevent insect attack and fungal decay.

How do you nail shiplap cladding?

Fixing shiplap cladding

For boards up to 150mm wide, use a single fixing located 25 – 30mm above the lower lap. Never nail through the lap joint. For boards over 150mm, use two fixings, with the second located a further 65 – 75mm above the first to allow for some dimensional movement.

Which way round do fence panels go?

Face the finished side of the fence toward your neighbor

In particular, the solid panel fences often used for privacy are generally constructed like this. The finished side should face toward your neighbor. Not only is this more polite, but it's the standard.

Should you use screws or nails for a fence?

Nails are faster than screws to install, meaning less labor for you or your builder (which may translate into lower installation cost). However, nails are more likely than screws to grow loose over time. Screws, on the other hand, secure the fence better than nails.

How many rails do I need for a 6 foot fence?

three rails

What kind of screws do you use for pressure treated wood?

The 2006 International Residential Code states, “Fasteners for pressure-preservative and fire-retardant-treated wood shall be of hotdipped zinc-coated galvanized steel, stainless steel, silicon bronze or copper. The coating weights for zinc-coated fasteners shall be in accordance with ASTM A153.

Can I use brad nails for fencing?

Pneumatic nailers can speed up many construction projects, but it's important to use the right-size nailer for the job you're doing. Brad nailers are suitable for cabinetry and interior trim, but the fasteners they shoot are too narrow and short to hold exterior fence boards, which have a tendency to move and warp.

What size nail gun do I need for fencing?

A framing nailer is used for larger projects such as fencing, deck building, roof sheathing, sub-flooring, and (of course) framing. Framing nail guns drive some of the larger gauge nails, from about . 113" to . 131" in diameter with lengths from 1-1/4" long to 3-1/2".

Whats stronger nails or screws?

When deciding between nails and screws, keep in mind that nails are less brittle, so they provide greater shear strength. Screws, on the other hand, may not be as forgiving, but their threaded shafts hold better in wood and draw boards together much more tightly and they have greater tensile strength.