How do you engage the blades on a Troy Bilt riding lawn mower?

To engage the blades, first, be sure that your throttle/choke lever is in the rabbit position. Then, push the PTO/Blade engage lever forward into the on position.

Likewise, why won't my lawnmower blades engage?

When the clutch solenoid is energized, the clutch engages the drive belt to drive the rotation of the lawn mower blades. If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage.

Similarly, what is a PTO switch on a lawn mower? ” PTO Switch Definition: PTO is an abbreviation for Power Take-Off, and it is a mechanical device or shaft that connects a tractor's power to another piece of equipment, like a spreader or snow blower. Do not repair your PTO while your equipment is operating.

Additionally, how do you adjust the PTO on a Troy Bilt riding lawn mower?

Place the PTO lever in the "Off" position and lower the mower deck as far as possible. Loosen the nut that holds the blade engagement rod in place. You can now shift the opposite end of the blade engagement rod slightly forward where it hooks into the adjustment slot.

How do you engage lawn mower blades?

How to Engage Lawn Mower Blades on a John Deere

Turn the key to the "on" position, advance the throttle to half speed and allow the engine to warm up for 2 minutes.
Lower the mower to the desired cutting height.
Engage the mower blades; push the lever to the right of the steering wheel all the way forward.

39 Related Question Answers Found

What is PTO blade engagement?

Engaging the Clutch

To get the blade to spin, the PTO clutch must be engaged. When the operator pulls the lever and engages the clutch, the pulley wheel springs outward and tightens the blade against the drive shaft pulley. The belt causes friction and grips the pulley.

What does PTO mean on a lawn mower?

Power Take Off

How do I enable PTO?

Make sure the transmission in neutral. While the clutch pedal is still pressed down, flip the PTO toggle switch to the “on” position. Depending on the Chassis type, The PTO switch is located on the dashboard above the transmission shift lever and is labeled “PTO”.

What is an electric PTO on a riding lawn mower?

An electric lawnmower clutch, commonly called a power takeoff clutch (PTO), is the part of a lawnmower or riding tractor responsible for engaging the blade. The electric clutch helps to transfer engine power to the drive train. The clutch connects two drive shafts and is controlled by a toggle switch.

How do I know if my PTO clutch is bad?

Activate the PTO clutch lever and look for the bulb to illuminate from the test light. No illumination means the engagement switch has failed at the lever-switch position. If the battery voltage reads correctly and the in-line fuse checks out, the lever switch will be the problem.

What is a PTO cable?

A power take-off or power takeoff (PTO) is any of several methods for taking power from a power source, such as a running engine, and transmitting it to an application such as an attached implement or separate machines.

Why does my riding mower keep throwing the belt?

The drive belt may come off a riding mower because it is damaged or loose. Even when it does not fall off, such a belt poses dangers. When loose, the belt may slip, resulting in friction that, if it creates enough heat, can lead to a fire in the mower's engine.

How can I make my Troy Bilt Bronco faster?

How to Make a Troy-Bilt Lawnmower Go Faster

Turn off your Troy-Bilt lawnmower. Open the front engine hood over the engine, if applicable.
Pull off the Troy-Bilt lawnmower's flywheel shroud to expose the flywheel and the parts underneath.
Find the lawnmower's magneto.
Find the Troy-Bilt lawnmower's carburetor.

How do you adjust the drive belt on a Troy Bilt riding lawn mower?

How to Replace the Drive Belt on a Troy-Bilt Lawn Tractor

Pull the mower deck lift lever all the way forward to adjust the mower deck to its lowest setting.
Unscrew the mower deck belt guard retaining bolts from the top of the left and right side mower deck with a socket wrench.
Unscrew the engine pulley belt keeper retaining bolt with a socket wrench.

How do you tighten the belt on a riding lawn mower?

How to Tighten a Riding Lawnmower Belt

Turn off the engine of your lawnmower and disconnect the spark plug wire as well.
Locate the main frame tube on your lawnmower.
Locate the belt, also known as the drive belt, inside the deck of your lawnmower.
Tighten the belt of your lawnmower by shortening the location of the main frame inside the clamps.

How do you change the drive belt on a Troy Bilt Pony riding mower?

How to Replace the Drive Belts on a Troy-Bilt Pony Lawn Tractor

Lower the deck to its lowest position. Use your tractors lever to move the mower deck to its lowest position.
Remove the belt guard.
Remove the belt from the pulley.
Remove the rear of the deck.
Remove the front of the deck.
Remove the PTO cable.
Remove the spring.
Slide the deck out.

Why does my Troy Bilt not start?

The carburetor might be clogged. A clogged carburetor is most commonly caused by leaving fuel in the lawn mower for a long period of time. This sticky fuel can clog up the carburetor and prevent the engine from starting. If the carburetor is clogged, try cleaning it with carburetor cleaner.

Are Troy Bilt riding mowers good?

With its affordable price tags, solid frames, and excellent features, Troy Bilt riding mowers offer great value for your money. This alone can make them a perfect pick for many so make sure to check out their wide selection of products if you think they may just have what you're looking for.

Why does my riding mower backfire when I shut it off?

During Shut-Off

When backfires occur as your lawnmower idles or as you're turning off the engine, the most likely problem is that you're slowing your engine speed too fast. Slowing the speed gradually and allowing the motor to idle for 15 seconds before you turn off the mower can help reduce these backfires.

What will cause a lawn mower not to start?

Your Mower Won't Start:

Other possible causes include: Loose, Dirty or Disconnected Spark Plug in Your Lawn Mower: Check it out, clean off debris, re-connect and tighten. Dirty Air Filter: Clean or replace. Fuel Not Reaching the Engine: Tap the side of the carburetor to help the flow of gas.

Why will my riding mower not start?

There are numerous explanations for why a riding lawn mower won't start, including everything from bad gas or a bad battery to a failed starter motor or bad ignition coil. A dead battery, bad starter solenoid, failed starter motor or a seized engine could be the cause.

What will cause a riding lawn mower not to start?

The most common reason for a riding mower cranking over but not starting, is bad gas, but other possible reasons include:

Gas Valve Off.
No Gas.
Choke Fault.
Plug Wet / Faulty.
Plug Wire Off.
Bad Battery.
Air filter Blocked.
Gummed / Faulty Carburettor.