How do you remove the pump on a Troy Bilt pressure washer?

Asked By: Strahil Shakespeare | Last Updated: 26th May, 2020
Category: home and garden home appliances
4.8/5 (779 Views . 42 Votes)
How to Replace the Pump on a Troy-Bilt Pressure Washer
  1. Disconnect the spark plug wire from the spark plug installed on the Troy-Bilt engine.
  2. Pull off the chemical hose from the pump nozzle, which is on the right side as you view the pump from underneath the pressure washer.
  3. Use a nut driver to unscrew and remove the three mounting bolts in the flanges on the pump.

Click to see full answer


Subsequently, one may also ask, how do you remove a pressure washer pump?

How to Remove a Pressure Washer Pump

  1. Disconnect all the hoses from the pressure washer and place on a firm, level surface.
  2. Spray penetrating oil along the top groove of the pump flange and along the joint where the flange connects to the engine.
  3. Remove the mounting bolts and washers holding the pump assembly to the engine using the correct size socket.

Likewise, how long does a pressure washer pump last? With higher quality pressure washers, the life expectancy of their pumps is closer to 500 hours. On average, households use their water pressure washer around 50 hours per year. This means that with a low cost pressure washer, the pump should last the average homeowner a year or two before it gives out.

Also know, can you repair a pressure washer pump?

Usually, you can replace the whole pump or any damaged part to start your lobby or garden cleaning again. It would take on average to replace the pump. You may repair by removing 3 or 4 bolts of the pump most of the times. Never think that the replacement of the pump will reduce the service.

Why do pressure washer pumps fail?

The two most important issues concerning breakdowns of pressure washer pump are cavitation and overheating due to excessive time in by-pass. Cavitation is caused when there is not enough water supplied to the pump. It is easy for the person a pressure washer to be distracted by something.

24 Related Question Answers Found

Can you upgrade a pressure washer pump?

By spending less than replacing the entire machine, you can have an upgraded pressure washer simply by purchasing a replacement pump. The pump is filled with oil when it arrives, so you can get to work immediately after fitting it. ?It's also super easy to install and use.

How do you prime a pressure washer pump?

Pressure Washer Tips: Operating procedures
  1. Clean any debris from the inlet filter.
  2. Connect any accessories (like this chemical injector).
  3. Run water through the washer for one minute to prime the system and remove any air.
  4. Squeeze the spray wand trigger to bleed water pressure.
  5. Pull the starter cord to start the engine.

What is a triplex pump?

Triplex pumps are positive-displacement reciprocating pumps that are configured with three plungers. They are the most common configuration of pump used in both drilling and well service operations.

How do you test a pressure washer pump?

[Back to top] Diagnosing By Symptom No matter what the symptom, diagnosing a pressure washer usually follows this order:
  1. Check the power supply.
  2. Check the water supply.
  3. Inspect all hoses.
  4. Take a look at the inlet valve.
  5. Check the intake filter.
  6. Inspect the nozzle.
  7. Inspect the gun.

What happens when motor locks up?


An engine seizes up due to mechanical failure, usually associated with oil starvation. As a result, if your engine locked up while driving, your engine will suddenly sound really rough, then stop on its own. Seized engines due to lack of oil can range from a little engine damage to major damage.

Why can't I pull the cord on my pressure washer?

If the starter rope won't budge when you try to pull it, the engine may be locked up or the recoil starter may have failed. If you tipped the pressure washer on its side recently, oil may have filled the cylinder, preventing the engine from spinning. Then reinstall the spark plug and try to start the engine.

Why is no water coming out of my pressure washer?

When no water is coming out of your pressure washer the first thing to check is the pressure nozzle itself. Particulate matter in the water, partially un-dissolved chemicals and other small bits can sometimes completely clog the nozzle. Likewise, the inlet water screen can become clogged by these same contaminants.

Can you unlock a locked motor?

The locking of the engine due to the fuel vapour is called engine vapour lock. In such cases, the engine can be unlocked by condensing the fuel vapour. For doing that you can let it sit for some time and try to start the engine. If the engine doesn't start, you can try splashing cold water on the fuel pump and lines.

How do I know if my motor is locked up?

Seized Engine Symptoms
  1. The most prominent seized engine sign is complete engine failure, i.e., no matter how much you try, the engine will not start.
  2. On cranking, loud clunking sounds can be heard from a seized engine, due to the stater hitting the flywheel.

How do you fix a pressure washer that won't start?


Your Engine Won't Start or is Lacking Power
  1. Run water through pressure washer until all air is removed from the hose.
  2. Check your air filter. Clean if dirty and replace if damaged.
  3. Check oil level. Change if needed.
  4. Top off fuel in tank.
  5. Make sure your spark plug is connected to the wire.
  6. If your engine was smoking:

What is the best pump for a pressure washer?

Best Pressure Washer Pumps
  1. Annovi Reverberi Kit Replacement Pump. Buy from Amazon.
  2. New Gasoline Premium Pressure.
  3. Universal Pressure Washer.
  4. Annovi Reverberi Pressure Washer.
  5. New Premium Pressure Washer.
  6. Homelite Universal Power Pressure Washer Pump.
  7. Annovi Reverberi Triplex Plunger Pumps.
  8. AAA Technologies Plunger Pump.

Can you put a pressure washer motor on a lawn mower?

98 inches, almost an inch) So if the length of the shafts are the same, you are getting close. Next, pressure washers have a heavy flywheel. It will work fine on a mower, but would be better off swapping your lightweight aluminum flywheel. While the flywheel is off, you can swap the blade brake/kill switch components.

How much oil does a pressure washer pump take?

In most cases, a single bottle of pump oil should be enough for at least one full oil change, if not more.