How do you attach chicken wire to the bottom of a fence?

Asked By: Ceferino Gueldenpfennig | Last Updated: 21st May, 2020
Category: home and garden landscaping
4.6/5 (1,821 Views . 15 Votes)
Place a tie at the bottom of the fence and another at the top of the chicken wire to keep your playful pooch from pulling the wire away from the fence. Continue securing the sections to the fence line until you've enclosed the whole fence in chicken wire.

Click to see full answer


Considering this, how do you attach wire mesh to a wood fence?

Hold the wire in place on the fence and apply the first staples to the post. Wear heavy gloves for the job to protect your hands from the wire. Unroll a couple of feet of wire, pulling it taut, and then staple to the fence rails. Keep unrolling and stapling, allowing about 24 inches between staples.

Furthermore, what can I put at the bottom of my fence? Rocks and Boulders Use the rocks to build a retaining wall along the bottom of the fence, or create a rock garden. For a slight gap, place a group of rocks and fill in around the rocks with dirt and perhaps some annual flowers to make it more attractive.

Accordingly, how do you attach chicken wire to a post?

Unroll the chicken wire a few inches and slip the horizontal wires along the first or second column of chicken wire cells into the tabs on a metal T-post and pinch them closed with pliers -- or staple across each horizontal wire down the first column of cells to fasten the wire to a wooden post.

What can I put on the bottom of my fence to keep my dog in?

Attach an L-footer along the bottom of the fence, facing in. You can use chicken wire, hardware cloth, or a piece of chain-link fence attached to the base of the fence. Some people bury it for aesthetic reasons. But you can also lay it on top of the grass and hold it down with rocks, gravel, mulch, or even planters.

34 Related Question Answers Found

How do you fix a mesh wire in a fence?

Open the tabs on a T-post one at a time from the bottom to the top of the post. Insert the wire mesh into the bottom tab and squeeze it shut with pliers. Continue attaching the wire mesh from the bottom to the top of each pole. Attach the wire mesh around the garden to all posts in the same manner.

How do you attach hardware cloth to a fence?

How to Attach Hardware Cloth to a Metal Fence
  1. Dig a trench 6 inches deep along the outside edge of the fence. Pile the dirt removed beside of the trench and discard the turf excavated from the trench.
  2. Unroll the hardware cloth next to the trench.
  3. Stand the hardware cloth up in the trench.
  4. Cut the hardware cloth with the wire cutters as needed to adjust the length.

How do you fix wire mesh on wood?

Hold the wire mesh in place, or have a friend hold it for you, and then press an industrial staple gun -- with staples slightly smaller than the depth of your frame -- onto the top corner of the mesh. Pull the trigger and insert a staple into the top left corner, and then the top right corner.

How do you make a T post welded wire fence?

Be sure that you mark out a section for the gate.
  1. Step 2 - Planting Your Posts. Use a post hole digger to dig at least 2 feet down.
  2. Step 3 - Rails. Measure and cut 1x4 boards for the top and bottom rails.
  3. Step 4 - Welded Wire Fencing. Start at a corner post and unroll several feet of welded wire.
  4. Step 5 - The Gate.

Do you have to stretch welded wire fence?


Welded wire fencing material cannot be tightened as much as woven wire meshes, such as field fence, horse fence, deer and wildlife fence. Don't forget to bring along a helper like Little Bit!

How do you make a simple gate out of chicken wire?

Screw the wood frame together with small, fine screw to ensure that the screws do not split the wood. Paint the frame (if desired) and let dry. Attach the hinges to one side of your chicken wire frame, spacing them approximately 1½ feet apart. Measure and cut your chicken wire using wire cutters to fit your wood frame.

How do you stretch chicken wire tight?

STEP 1) Stretch the Chicken Wire Past the Post
  1. Stand just past the post that doesn't have the chicken wire attached to it.
  2. Using gloves slide your fingers into the holes in the middle of the chicken mesh roll.
  3. Pull it firmly to stretch the chicken wire across past the post that isn't attached to the chicken wire.

How tall should a chicken fence be?

A fence to keep chickens in has to be 6 foot or 1.8 metres high. I recommend the same to keep bantams inside the yard so they can free range.

How deep should chicken wire be buried?

The bottom of the fence
The bottom of a poultry fence, should have the wire buried 8-12 inches in the ground and then turned outwards by about 8. The length of wire you bury really depends on the type of soil and how level the ground is.

Can you use chicken wire for dog fence?


The best solution is to build a fence so your dog can walk freely in your yard. Chicken wire is an inexpensive material you can use to build your fence.

How do you keep chicken wire in the ground?

Dig a 12-inch deep, 6-inch wide trench along the bottom of the fence. Remove rocks and debris from the fence line and dig down into the soil, taking care not to dig through any sprinkler or water lines. If the ground is too hard to dig through, soak the dirt with a garden hose for a few minutes to loosen the soil.

How do you fill gaps at the bottom of a fence?

Multiply the length of the gap by the height and width of the gap to determine the cubic feet of the area. Purchase enough rocks or stones to fill the volume. Dump the rocks or stones into the gap beneath the fence. Use a bow rake to spread the rocks or stone over the area.

How do you block the bottom of a fence?

How to Fill Gaps Under Fencing
  1. Stones. Use decorative stones or river rocks that are between 1-3 inches in diameter to fill the gaps under your fencing.
  2. Wood Pickets. If you have a wood fence with gaps under the fencing, blocking them can be a little bit more labor-intensive.
  3. Concrete Blocks.
  4. Choose Hercules Fence Richmond!

How do you keep the bottom of a fence from rotting?

What Causes Wood to Rot:
  1. Dry Rot. Dry rot occurs when a wooden fence loses the natural oils on its surface.
  2. Wet Rot.
  3. Use Proper Wood.
  4. Use Pressure-Treated Materials.
  5. Install Properly.
  6. Protect With Stain.
  7. Keep The Fence Clean.
  8. Replace Rotted Wood.

How do you protect the bottom of a wood fence?


If you want to protect the fence, I see three options:
  1. Cut the bottom end of the pickets so it's no longer touching the dirt.
  2. Add stone/gravel to provide free-draining surroundings as you suggest.
  3. Remove some dirt near the fence (may be too much work, or against your landscape design goals).

What is the board at the bottom of a fence called?

Pickets, also called slats or boards, attach to the backer rails with nails or screws. They make up the body of the fence and are therefore the most visible component of the fence project. Pickets are available in multiple top styles such as dog ear, flat top and french gothic.

How do I fix my fence so the dogs don't get out?

For digging dogs: Bury chicken wire at the base of your fence (with the sharp edges rolled inward), place large rocks at the base or lay chain-link fencing on the ground. Never chain or otherwise tether your dog to a stationary object as a means of keeping them confined.