Can you put Hardie board over drywall?

Because cement board can be used either for floors or walls, the surface below the cement board will vary: In such wet areas, never install cement board directly over drywall or green board. Instead, first, remove the existing surface material, then install the cement board over the studs and membrane, as applicable.

Similarly one may ask, how do you install Hardiebacker on drywall?

For most shower walls, the drywall installed in the home during the building phase is cut off at the edge of the shower opening, and then backer board is installed in place of the drywall in the wet areas. The backer boards are usually around a one-half-inch thick in both cases.

Beside above, can you put backer board over drywall for kitchen backsplash? Ideally, when installing backer board over drywall or plywood, either on the floor or the wall, you should apply a layer of thinset on the wall between the backer board and the wall. This eliminates any gaps or areas that would otherwise allow the backer board to flex.

Besides, can you put stacked stone on drywall?

Regular stone requires backer board, but you can apply stone veneer directly to most surfaces, including drywall, concrete or brick. The stone veneer stacks tightly so you can't see the surface underneath. It also comes in various lengths, which allows for natural-looking offset seams.

Can you put tile over drywall in bathroom?

Sheetrock, or drywall, is no different for tiling over than wood, plaster, cement, or other wall materials. If you are tiling an area that is not in a bathroom, tiles can be applied directly to the sheetrock simply and easily. The wall has to simply be prepared in order to complete this task properly.

39 Related Question Answers Found

Do you have to put drywall behind cement board?

Because cement board can be used either for floors or walls, the surface below the cement board will vary: In such wet areas, never install cement board directly over drywall or green board. Instead, first, remove the existing surface material, then install the cement board over the studs and membrane, as applicable.

Which side of Hardie board goes out?

Cement board has a smooth side and a rough side. Face the rough side out if you will be using thin-set mortar adhesive to install the tile but the smooth side out if you will be using latex mastic.

Do I need to Thinset under Hardibacker?

Since you are putting down hardie board on boards with small gaps, I would not recommend trying to put down thinset under it. It will make an enormous mess under the house (or whatever is under your bathroom). It is also more likely to make the floor uneven since it is hard to level thinset that is separated by gaps.

Does drywall go behind bathtub?

Drywall should not sit directly on the tub as it can "wick" moisture and will eventually fall apart (even green board) if the tub is not kept caulked properly. There is no need for drywall behind the cement board and I have never heard of it being done that way.

Do you need to tape cement board before tiling?

2 Answers. The thinset and mesh tape are to strengthen the seams. If you are going to tile over the cement board, you should tape the seams. If you just want to leave the corners untreated that will probably be fine, because that seam won't split the center of a tile.

What kind of Thinset do you use for Hardibacker?

To save a few bucks, you can use dry-set mortar under Hardi, but if you want to simplify things and deal with only one thinset, use a modified thinset like 253 Gold for both applications. Rialto is a porcelain tile that has deep depressions on the back.

How many screws go into a sheet of drywall?

Drywall screws per sheet. Drywall screws should be installed every 12 inches. This means that when using 48 inch wide sheets, you will have 5 screws in each stud when the sheets are hung perpendicular to the framing; two on the edges and 3 in the field.

Does Thinset stick to drywall?

Thinset bonds best with a porous surface, such as new drywall or backerboard, which needs no preparation, but you can apply it over painted walls or tiles that are flat and in good condition as long as the shiny finish is removed. Use the type of thinset mortar specified for your particular tile.

Do you grout stacked stone?

What You Need to Know About Stacked Stone. The three-dimensional veneer is made of cut pieces of natural stone that are attached to a backing and installed like you would tile. The material uses no grout; in fact, the dry stacked look is part of its appeal.

What glue to use for stacked stone?

Glue Type and Use

Contact cement, silicone adhesives, epoxy glues and all-purpose construction adhesives can all work with natural stones. Glue can be found in buckets and you use a notched trowel to apply the glue to the wall, such as with natural stone mastics.

How do you install metal lath on drywall?

expanded, galvanized, metal lath to each stud 6” on center-vertically, penetrating the studs at least one inch. Be sure to attach the lath horizontally. The surface should feel rough as you rub your hand upward. Install lath with a minimum 1” overlap on horizontal and vertical seams.

How much does a stacked stone fireplace cost?

Install stacked stone veneer Costs. For your project in zip code 98104 with these options, the cost to install stacked stone veneer starts at $22.98-$29.12 per square foot. Your actual price will depend on job size, conditions, finish options you choose.

Do you need special drywall for kitchen backsplash?

A tile backsplash in the kitchen may be applied over clean, level drywall since sinks are not considered wet areas, like showers, that require backer board. Also before you start, remember that using the correct trowel and mortar is critical to a successful tile project.

Is backer board necessary for backsplash?

to answer your question, no you don't have to put backerboard up for a tile backsplash. ( if you are useing the traditional 4x4 tiles made from talc powder. These are very light weight and will never need to withstand any weight on them. You can even put them over plaster.

Should I use mastic or thinset for backsplash?

Use the Proper Adhesive

Tile is often installed with thinset mortar. But for a backsplash wall, consider using tile mastic. In addition, mastic holds faster than thinset mortar, so there's less chance of the tile sliding down the wall while you're working.

Can tile be installed over painted drywall?

You may tile over existing tile, painted or unpainted drywall, plaster and textured walls. However, tiling over tile can add quite a bit of thickness, so make sure your wall can handle the weight. You should not tile over wallpaper, glossy surfaces, lead paint or plywood.

What's new in kitchen backsplashes?

This Hot Kitchen Backsplash Trend Is Cooling Off

Ditch: Cement Tiles.
Invest in: Handmade and Organic Materials.
Ditch: Trendy Patterns or Colors.
Invest in: Marble.
Ditch: Short Backsplashes.
Invest in: Enough Tile to Reach the Ceiling.
What to Ditch: Subway Tiles.
Invest in: Out-of-the-Box Shapes and Textures.