Why is my toilet on a raised platform?

The raised platform is used in order to have the correct angle for the sewer pipe to run with a down angle to the top of the black tank. You can't take the platform out because you will continously block the sewer pipe. You could build a raised platform in front of the toilet so your feet hit the ground.

Likewise, people ask, can a toilet be raised?

Raised toilets seats can range from 2 to 6 inches above the original seat height. There are also a variety of wider options than regular toilet seats. It's also possible to get toilet seats with adjustable heights and widths, if you're not sure which size to get.

Beside above, what is a back flush toilet? Back outlet toilets connect to a plumbing "rough-in" positioned on a bathroom wall rather than on the floor. They use a toilet connection located at the back of the bowl rather than the more common placement of directly below the bowl. All toilets have to connect to a sewer line to dispose of waste.

Then, how do you build a raised platform for a bathroom?

How to Build a Platform for a Bathtub

Check the height of the platform that your tub requires and calculate the height of the platform wall studs.
Nail the studs to the top and bottom plates to form the walls for the platform.
Secure the wall framework to the floor with nails, and use deck screws to cover the framework with plywood to make the deck.

Can toilet flange be higher than floor?

With the toilet removed, you can see the toilet flange and measure its height above the floor. Optimum flange height to aim for is 1/4 inch above the finished floor. This typically allows for almost any type of wax ring to be used and still ensure a good seal.

39 Related Question Answers Found

Can toilet flange be lower than floor?

In a typical toilet installation, the floor flange that sits inside the drain opening below the toilet should be flush with the finished floor, or no more than 1/4 inch above or below the floor.

Should I get a comfort height toilet?

Just like shoes, you should feel comfortable with the right toilet sitting height. You should be able to sit down and stand up without any struggle. That's when an ADA or comfort height toilet can make a difference. A standard size toilet will have a seat height of between 15 to less than 17 inches.

How do I reinstall my toilet after tiling?

Follow the directions provided below to set the toilet ring into the flange after tiling the floor.

Step 1 - Seal the Drain Hole Before You Start Work.
Step 2 - Adjust the Toilet Flange Height to the New Floor.
Step 3 - Remove the Old Toilet Flange Bolts.
Step 4 - Attach the Toilet Ring to the Toilet Bowl Base.

Can you put a shower where a toilet was?

If you are remodeling your bathroom and find that the shower will be installed over the location of the previous toilet, you can simply change the toilet drain to a shower drain.

How do you build a raised concrete floor?

How to Build a Raised Floor Over Concrete Slab

Understand Where You're Applying It.
Select Your Raised Access Floor Type.
Determine the Floor Height.
Select the Right Load & Weight Ratings.
Select Your Panel Material.
Be Mindful of Regulations & Standards.

How do you build a shower pan on a concrete floor?

Install the pre-slope. Pre-slope is required in order to allow water collected on the shower membrane to drain into the weep holes of your shower drain assembly. Remember, tile and mortar are NOT waterproof. Using concrete mix, create a 1/4" per foot slope to the shower drain.

How do you raise a shower floor?

Make the floor thin-set mortar as thick as desired to raise the concrete shower platform. Use the shower floor slope tool to ensure that you keep the 1/4 inch slope on the floor to allow for proper water drainage. Wait 24 hours before installing the shower floor and wall tile on the shower curb.

How do you install a corner bath?

Refer to your bathtub manufacturer's framing instructions and decide on your framing layout. Using your saw, cut your lumber into pieces that fit the size of your frame. Attach the pieces together using screws and a screwdriver. Next, use your studfinder to locate the studs in your corner wall.

How do you install a low profile shower tray on a concrete floor?

Apply a thin bed of flexible adhesive to the area where the tray is to be secured using a notched trowel. Fit the shower tray over the bed of adhesive and firm down ensuring the tray is level in all planes Identify the position of the drain and trap and remove any existing concrete to a depth of approx.

Where is the P trap in the toilet?

A toilet trap, or trapway, is a curving channel inside the base of a toilet that leads from the hole at the bottom of the bowl to the drainpipe. When a toilet backs up and the clog did not occur in the drainpipe, the stoppage usually exists in the trap.

How do you install a back drain on a toilet?

Connect the water supply tubes at the bottom of the tank. Turn on the water supply and flush the toilet several times to check for any leaks around the back or base. Attach the toilet seat by placing it on top of the bowl and securing it in place with supplied bolts.

What is a macerating toilet?

Macerating toilets use a grinding or blending mechanism to reduce human waste to a slurry, which can then be moved by pumping. This is useful when, for example, water pressure is low or one wishes to install a toilet below the sewer drain pipe.

How do you rough in plumbing?

Steps for Roughing in your Plumbing:

Step 1)Mark Key Locations. Determine where all the toilets will be and mark its center on the wall and measure out 13 1/2 inches from that point.
Step 2) Cut the Drain Hole.
Step 3) Drain Pipe Installation.
Step 4) Supply Line Installation.

Are all toilets in a house connected?

1: All drain pipes should be connected to a network of ventilation pipes that go up through the roof. The toilet drain is the largest drain pipe in the house. 4: All household drains meet below the house in a main drain that carries the wastewater to the municipal sewer lines or to a septic system.

How do you drain a toilet?

To drain a toilet tank, start by turning the small knob at the base of the toilet clockwise to shut off the water supply to the toilet. Next, carefully take the top off of the toilet tank and set it aside. Then, flush the toilet, which will cause the water in the tank to start to drain.

What is a pressure assisted toilet?

Pressure-assisted toilets have a tank inside of another tank so that a large amount of air pressure is created in between the two tanks. This pressure makes it possible for more water to stay inside the toilet bowl, which, in turn, results in a cleaner toilet.

Does toto make a rear outlet toilet?

TOTO does not make a floor mounted rear outlet bowl. They do make commerical bowls that use a Sloan type valve that use a wall carrier. These would not be recommended for homes. To use any commerical flush valve in a home would require repiping the home all the way to the water meter.