Why is my pool robot going in circles?

Sometimes it gets stuck in the corner of the pool by the steps; other times it goes in circles. This is most likely caused when pool cleaners are left in the pool 24/7. When the water is cold or cools off from a warm day, the plastic in the hose gets a memory and curls slightly.

Similarly, why does my pool cleaner keeps stopping?

When a suction cleaner is sluggish or slow, it's usually a clogged pump basket or dirty filter that is to blame. Other problems include holes in the cleaner hose, sucking air into the hose. Or the filter pump could be drawing in air, reducing water flow volume.

Secondly, how do you adjust the thrust on a Polaris pool cleaner? How to Adjust the Thrust Jet on a Polaris

Remove the unit from the water: Shut off the pool pump system and lift the Polaris vacuum unit out of the water, lifting it by its hose.
Moving the jet nozzle on a Polaris pool cleaner affects how it moves in the pool.
Test the Polaris: Lower the Polaris by the hose back into the pool.

People also ask, why does my Hayward Navigator go in circles?

Is it spinning in circles or getting stuck in corners instead of going around the pool? There are an assortment of gears and moving parts inside the Navigator that need to be checked and replaced now and then. Sometime, it's just debris interfering with the movement of the gears.

Why does my creepy crawly keep getting stuck?

Water Flow The returning water pressure can be pointed at a corner that the cleaner is stuck in to help move the hose out of a corner thus allowing the unit to clean the pool more effectively and becoming less maintenance and causing ware on the head of the cleaner.

36 Related Question Answers Found

How do I find a leak in my pool vacuum hose?

Detect the Points of Leakage:

Start by filling the hose with water. Once the hose is full, slowly lift it up while keeping the head of the vacuum under water. When the leakage point goes above water level, the pump will suck air into the hose, thus forming bubbles. The leakage is at the point where you see the bubbles.

How does a pool creepy crawly work?

A Kreepy Krauly draws water from the bottom, top and sides of your pool ensuring circulation of pool water and improving water quality. Because your Kreepy Krauly works with your pool pump this cleaning process occurs automatically with daily cleaning cycles and may reduce your need for chemicals.

What pressure should a pool filter run at?

A pool system's pressure is generally measured at the filter's pressure gauge; the usual range is 10 - 25 pounds per square inch (PSI.) When you installed your filter, or after a thorough cleaning, make a note of the “clean filter” PSI. This rating will be used as a benchmark for pressure tests down the line.

Why is my automatic pool vacuum not moving?

If the vacuum doesn't work, it's usually either because air is getting into the vacuum hose or into the suction side of the pool pump. The presence of air in the lines is preventing the system from drawing water as it should.

How do you clean a pool filter?

Cleaning with Muriatic Acid

Backwash the filter for 3 to 5 minutes to remove debris.
Turn the pump off.
Open the air relief valve.
Remove the drain plug, and let the water drain out of the filter tank.
Remove the clamps (or other latching mechanisms) holding the filter together.
Open the filter tank.

How long does a Hayward pool vacuum last?

The idea is that pressure side cleaners can last more than eight years, as their parts can usually be replaced. This is an added maintenance cost. A robotic pool cleaner would be expected to last between 3 to 5 years and may last up to 8 years.

How long should my pool vacuum hose be?

The vacuum hose should be long enough to reach the entire pool from the skimmer you are using. So it depends on your skimmer inlet.

How does a Hayward Navigator work?

Hayward's exclusive technology harnesses the flow of water through the filtration system to drive the Navigator Pro in an alternating series of right- and left-hand turns. This systematically cleans pool surfaces and ensures the best coverage, as well as the most efficient cleaning path.

How do I adjust my pool vacuum?

VALVE SETTINGS - VACUUMING MODE

Sink the hose and plug it into skimmer.
Connect the vacuum head to the pole and then connect the swivel cuff on your vacuum hose to the vacuum head.
Drop the vacuum head into the pool and "sink" the hose.
Push the other end of the vacuum hose into the suction port at the bottom of the skimmer nearest to the pump.

Why is my Polaris pool cleaner floating?

A Leaky Hose

Leaks in the Polaris hose cause the cleaner to lose pressure, allowing it to float above the pool bottom. To check for leaks, turn the system on and pull the hose out of the water one section at a time, looking for bubbles or trickles of water.

What does the Polaris backup valve do?

The Polaris Back Up Valve is a mechanism attached to the cleaner's feeder hose, which helps the Polaris cleaner maneuver the floor of your pool. If this item is malfunctioning then your cleaner may not be able to clean effectively.

How do you adjust a Polaris pressure relief valve?

How do I Adjust a Polaris 280?

Step 1 Adjust Nozzle Direction. Shut down water flow to the Polaris 280 and take the device out of the pool.
Step 2 Adjust Hose Length. Unscrew the nut connecting the Polaris hose to the Polaris body, and pull the hose free.
Step 3 Check Wheel Rotation Speed.

How far should the back up valve be from the Polaris?

The Polaris in-line back-up valve and float should be installed 30" from the Polaris.

Is it better to run a pool pump at night or day?

Is It Better To Run Your Pool Pump At Night Or During The Day? Running the pump at night should only be when you are doing a major chemical treatment such as algae clean-up. Your pool is more vulnerable during the day, plants don't grow at night the way they do during the day–that's true of ALL plants including Algae.

Can I leave my Polaris in the pool?

In The Industry

Most have a filter bowl on the Polaris return line near the pump. No problem with leaving the Polaris in the pool when not in use.

How often should I run my Polaris pool cleaner?

run the 280 for as long as it keeps the pool clean, this could be 1 hour per day to 6 hours per day depending on the amount of debris is in the pool, but remember the 280 has gears and cogs so the more you run it the quicker it will wear out. On average it should take about 3 hours to clean a standard size pool.

How does Polaris pool cleaner?

Polaris Pressure-Side Pool Cleaners for Inground Pools. They work in any type of inground pool. They're also powered by your return jets, but some require a booster pump to provide optimum water pressure. These cleaners feature small water jets that create a vortex which pulls debris up into the filter bag on top.