What size are toilet bolt nuts?

A set of replacement toilet caps typically includes two different sets of threaded adapters: 1/4 inch and 5/16 inch. The 1/4-inch size is the more standard.

Likewise, what size are toilet bolts?

The job of the toilet bolt is to help create a watertight seal between the toilet bowl and the toilet flange and to secure the toilet to the floor. There are three possible measurement distances you can get from the wall to the toilet bolt: 10 inches, 12 inches or 14 inches. The most common is 12 inches.

Secondly, how do you change a 2 bolt toilet to a 4 bolt toilet? Throw away the old toilet bolts and clean all the old wax with a putty knife. Set two new bolts in the flange, place a wax ring on the bottom of the new toilet and set it in place. Sit on it to spread the wax, then tighten down the bolts, hook up the water and fill the tank.

In this manner, what size are toilet tank nuts?

The stainless steel nuts and washers are also included for complete replacement of all old hardware. Tank Bolts are proven durable, and the 5/16” size x 2 ¾” length will fit most brands and models. Repair your rocking toilet tank with new toilet bolts.

How tight should a toilet bolt be?

The toilet bolts should not be overtightened, but they should be tight. If you hear the sound of metal on porcelain, stop tightening. But if you still feel the bolts tightening against the wax ring, keep going.

35 Related Question Answers Found

Should I caulk around toilet?

2. Caulk helps to keep the toilet secured to the floor. The bolts are really supposed to keep the toilet secure, but caulk helps. Some people prefer to caulk all around the toilet and leave about a one-inch gap in the caulk at the back of the toilet to allow water to escape out in the event of a leak.

How do you measure a toilet?

Measure from the wall behind the toilet to the center of one of the closet bolts (that hold the toilet down). If the toilet has four closet bolts, measure to the center of one of the rear ones. Measure from the center of the mounting holes to the back of the new toilet you're considering.

What causes a toilet to wobble?

More often than not, the wobble is caused by loose toilet bolts, but the flange may also be responsible. It may be corroded, broken or set too high. Moreover, the person who installed the toilet may have used a wax ring that is too thick. If you can't get the toilet to stop wobbling, loosen the nuts and remove them.

How tight should toilet tank bolts be?

on each bolt, on bottom side of tank, put another rubber washer then another flat washer, then a nut. tighten nut a little past hand tight. not too much, don't distort the rubber washers. that should give you a watertight double seal at the bottom of the tank.

Are toilet seat bolts universal?

They are universal and much better than the plastic bolts which break too easily. There is no more slipping of the toilet seat too!

Are toilet tank bolts universal?

Manufactured in a high quality, chlorine resistant rubber, the Korky tank to bowl gaskets are universal to fit most toilet tanks. All kits are offered with and without tank to bowl hardware.

How do I change the bolts on a toilet seat hinge?

Standard metal hinge with residential Sta-Tite®

Thread the bolt into the hinge.
Push the bushing all the way up bolt until it's flush with the hinge.
Place toilet seat bolts into toilet bowl.
Finger-tighten Sta-Tite® nut onto bolts.
Align toilet seat onto bowl and use a 1/2" wrench to tight bolt.

How do you install a bolt cap on a toilet?

Installation is easy, simply remove your old cap and nut, set the base, anti-spin washer, and old nut, then screw-on the cap, and you're done. Choose Fluidmaster Smart Cap Toilet Bowl Bolt Caps to easily cover up bolts in just a few minutes.

How do you fit close coupling cistern bolts?

Lift the cistern onto the pan so the connecting bolts fit through the holes. The threaded section of the flush mechanism should go through the rubber gasket on the flush entrance of the pan. 3 Fit washers to the connecting bolts, and tighten the wing nuts. Make sure you fit these securely, but don't over-tighten them.

What are the parts of a toilet?

Bowl: The round part of the toilet that holds water and waste. Tank: The back part of the toilet that holds the water used for flushing. It also houses the working toilet parts. Stop Valve: This controls the water supply to the toilet.

How is a toilet bolted to the floor?

Toilet anchor bolts hold your toilet to the floor and keep it connected to the flange, which is the opening to the waste line. Moisture around the base of the toilet can corrode the anchor bolts. Grip the top of one of the bolts with adjustable pliers, then fit an adjustable wrench around the nut.

How is a toilet connected to the floor?

Proper Connection

When properly connected, the toilet rests on top of the toilet flange, with the wax ring providing a seal to the floor. The flange bolts that fit up through the toilet's mounting holes are each held secure by a washer and nut, thus providing the toilet's connection to both the floor and the drain.

Does a toilet need to be bolted down?

The flange should be fastened to the floor. Dry fit the toilet to make sure it doesn't rock. If it does rock, use shims to prevent rocking - just tightening the bolts probably will not stop the rocking but will risk cracking the toilet or breaking the flange. We would usually screw it down during the rough in.

How do you replace the wax ring and bolts on a toilet?

Use a putty knife to scrape away as much of the old wax ring as you can from the flange, a pipe fitting where the toilet mounts to the floor, and around the toilet drain. Remove any debris, smooth and dry the surfaces, and remove the two bolts from the flange. Look closely at the condition of the flange.

How do you tighten the bolts on a toilet?

Check the flange bolt at each side of the toilet, using a pair of pliers or a small wrench. If a bolt is loose, tighten it slowly just until it is snug. Check the other bolt to make sure it is equally snug, then test the toilet for rocking. If it still rocks, proceed with shimming the base.

How do you measure rough in for toilet?

To find out your toilet's rough-in, measure from the wall behind the toilet to the middle of the closet bolts, which hold your toilet to the floor. That distance will likely be a bit more than the standard 10″, 12″, or 14″ rough-in dimensions. Round your measurement down to the nearest standard rough-in.

Do Toilets need to be replaced?

Some cracks and leaks can be safely repaired without replacing the entire toilet, but it's better to be safe than sorry. If you have a crack in your toilet that's actively leaking, you should get it replaced immediately. If your toilet does enough water damage, it could wind up crashing through the bathroom floor.