What does the Code OE mean on a Samsung washer?

Asked By: Billi Chiachio | Last Updated: 14th March, 2020
Category: home and garden home appliances
4.3/5 (1,621 Views . 16 Votes)
water overflow error

Click to see full answer


Hereof, how do I fix the OE code on my Samsung washer?

Run tub clean cycle. Once the drain pump begins sucking air instead of water, the pump signals a drain issue to the unit. Perform a TUB CLEAN CYCLE and REDUCE DETERGENT usage. Run the new cycle to see if the code is cleared. If the OE error code appears again, the unit may require a repair service.

One may also ask, what are the codes on a Samsung washer? Samsung Front Load Washer Fault Codes

Fault Code Washer Problem
LO or FL Door lock error
ds Door is not locked
dc Unbalanced load
Sud (F70) Too many suds

Then, how do I know if my washing machine drain pump is bad?

If the motor and pump is running but no water is draining out then most likely the 3363394 pump is bad. One thing you can try first is to lower the drain hose over a shallow pan and see if the water in the tub will drain by gravity. If not then there may be a sock or other obstruction blocking the pump.

How do I manually drain my LG washer?

Press the POWER button to turn the washing machine off and remove the plug from the outlet. Locate the service panel on the bottom-left corner of the unit and open it. Unclip the drain hose and remove the plug from the drain hose to drain the water remaining inside the wash tub.

35 Related Question Answers Found

How do I troubleshoot my Samsung washer?

SAMSUNG WASHER FIX/SOLUTION:
  1. Check the fuse or reset the circuit breaker.
  2. Straighten the drain hoses.
  3. Eliminate kinked hoses.
  4. If there is a drain restriction, troubleshoot it.
  5. Close the door and press the Start/Pause button.
  6. For your safety, your washer will not tumble or spin unless the door is closed.

How do I fix my Samsung e3 error on my Samsung washing machine?

How To Fix 3E Samsung Washer Error Code:
  1. Unplug The Washing Machine: Unplug the washer for 2-3 minutes.
  2. Check Wire Connections On Drive Motor: One fairly common issue that causes the 3E error code is connection problems.
  3. Check Wire Connections On Control Board:
  4. Check Hall Sensor:

How do I reset my Samsung washing machine?

  1. Turn the washing machine off and then on again.
  2. Hold down the Temp. and Delay End (+) buttons simultaneously for 3 seconds. CB or CLB will appear on the display.
  3. Press the Start/Pause button to begin Calibration Mode.

How do I fix OE error on my LG top load washer?

OE Error Code - Top Load Washer
  1. Press POWER to turn the washer on.
  2. Press the SPECIAL USE key until SPIN ONLY is lit.
  3. Press the START/PAUSE button to begin the cycle.
  4. The unit should begin a SPIN ONLY cycle and attempt to drain any remaining water that is inside the washer.

How do you diagnose a washing machine problem?


Remove the power source to the washer before troubleshooting or attempting repairs.
  1. #1 - Washer Won't Turn On.
  2. #2 - Not Draining Properly.
  3. #3 - Will Not Spin and/or Agitate.
  4. #4 - Washer Leaking Water.
  5. #5 - Does Not Dispense Detergent.
  6. #6 - Washer is Shaking and Moving.
  7. #7 - Washer is Noisy.
  8. #8 - Washer Smells.

How much does it cost to replace a washing machine drain pump?

Below are average costs for common washing machine replacement parts, though they vary widely by brand: Water or drain pump: $35-$200. Drain hose: $3-$30. Motor: $150-$500.

How do you fix a washing machine that will not drain?

If the washer won't drain there might be a clogged pump or hose. It's common for small socks or other small clothing items to get into the water drain system and clog the hose leading to the pump or the pump itself. Remove the hoses from the pump in order to remove the article of clothing.

How do you fix a washing machine drain pump?

How to Repair a Washing Machine
  1. Step 1: Check the drain hoses to make sure they're draining properly.
  2. Step 2: To access the pump, first bail and sponge out any water in the machine's tub.
  3. Step 3: Locate the pump.
  4. Step 4: To remove the pump, loosen the bolt that holds the drive belt taut and move the washer motor on the bracket to loosen the belt.

Why is my washing machine filling up and draining at the same time?

Answer: Your washer DRAIN HOSE is causing a siphoning condition. Your washing machine drain hose is pushed way too far into the stand pipe in the wall. This creates a vacuum or siphoning affect and the water is pulled out of the washer as it fills with water.

Why are my clothes still soaked after washing?


If the drain hose on the back of your washer is too far down or not down far enough in the standpipe, this can cause an issue with proper draining and can cause the washer to not fully drain out the water and therefore your clothing will still be soaking wet after a wash cycle.

What do the symbols on washing machine mean?

Symbols on Washing Machine Detergent Drawers
Once you have your clothes ready and the best wash cycle, temperature, and spin selected, it's time to add what your clothes need to become clean: Detergent, fabric conditioner, and pre wash! I= pre wash. II= main wash. Flower symbol= fabric softener.

How do I fix e4 on my washing machine?

When the washing machine issues the E4 error, you need to open the door and spread the laundry in the drum. Typically, the door opens five or seven minutes after the code appears on display.

What does e3 mean on a Samsung washing machine?

The meaning of the E3 error code
The E3 error in Samsung washers means a drum overflow with water. The water level sensor sends a signal indicating that there is too much water in the drum. More precisely, there is more water than required for the selected program.

How do you reset a front load washer?

How to reset the washing machine:
  1. Press POWER to turn the washer off.
  2. Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
  3. With the power disabled, press and hold the START/PAUSE button for 5 seconds.
  4. Plug the washer back in, or turn the circuit breaker back on.

How do you force a washing machine to drain?


Drain a Top-Loading Washing Machine
  1. STEP 1: Turn off the power. Switch the power button on the machine off, if your model has one.
  2. STEP 2: Locate the drain hose and water supply hoses.
  3. STEP 3: Drain the washing machine of water.
  4. STEP 4: Remove a drain hose clog.
  5. STEP 5: Remove a drain pump clog.

Why is my LG front load washer not draining?

If the washer won't drain or is not draining properly, and the washer has a coin trap, remove the coin trap and clean it thoroughly. First, check the drain hose to determine if it is kinked, twisted, or bent. hose has any obstructions, try to remove them. If necessary, replace the drain hose.

How much is a drain pump for a LG washing machine?

LG 4681EA2001T Drain Pump Washing Machine
List Price: $49.95
You Save: $20.46 (41%)