Is beadboard cheaper than sheetrock?

Asked By: Maximilia Altemann | Last Updated: 28th January, 2020
Category: hobbies and interests woodworking
4.1/5 (500 Views . 43 Votes)
The least expensive option between drywall and beadboard is paneling, which is easier to install and less costly per-square foot. However, consider the quality prior to installation, as it sometimes is not worth the savings to have low quality drywall or beadboard.

Click to see full answer


Besides, is paneling cheaper than sheetrock?

Cheap 3/16 inch fake wood or patterned panels can cost around $10 per panel. A decent real wood veneer can soar to $40 each. It is common practice to put paneling over drywall. If anything, if paneling is not installed over drywall, the seams can be a source of air infiltration, negating any insulation value.

Also, is shiplap cheaper than drywall? First of all, Shiplap can be more expensive than drywall. It all depends on the materials used. Some shiplap materials used are also cheaper than drywall. While drywall is considerably less costly than some shiplap materials, there may be many reasons why you should consider the later.

Also Know, can you use beadboard instead of drywall?

Prep the Wall Surface Also remove and save any window trim that will be in the way. The moldings will be replaced over the beadboard in the finished project. Beadboard may be installed over drywall or old plaster providing these materials are solidly attached to the wall framing.

Whats cheaper than drywall?

While it's cheap and easier to work with than other materials, drywall installation remains a tough process that involves taping, mudding, and sanding.

  • Wood Planks.
  • Plastic Panels.
  • Plywood.
  • Veneer Plaster.
  • Pegboard.
  • Lath and Plaster.
  • Wahoo Walls.
  • Textured Wall Panels.

39 Related Question Answers Found

What are alternatives to drywall?

10 Types of Drywall Alternatives for Your Walls
  • Lath and Plaster. Lath and plaster used to be a more time consuming wall surface to install, however, over time, the system has evolved and is now a quicker and easier form of wall to install, and makes a nice alternative to drywall.
  • Cement Board.
  • Plastic Panels.
  • Concrete Walls.
  • Wood Planks.
  • Brick.
  • Veneer Plaster.
  • Pegboard.

Can I use plywood instead of drywall?

Plywood is a viable alternative to drywall for walls and ceilings. If you are planning on redoing your walls or ceilings, the typical materials you'll use include Sheetrock or finished plywood. Each has its benefits as a building material and in some cases, finished plywood is the better alternative.

Is it OK to drywall over paneling?

Drywall can be installed over wood paneling that is in good condition. Removing paneling can be a time-consuming and costly so many homeowners opt to drywall over the paneling. Installing drywall over paneling is a workable solution if it is done properly.

What is wood paneling on walls called?

Panelling (or paneling in the U.S.) is a millwork wall covering constructed from rigid or semi-rigid components. These are traditionally interlocking wood, but could be plastic or other materials. Panelling was developed in antiquity to make rooms in stone buildings more comfortable.

Is Wood a better insulator than drywall?


Basically the difference between drywall and wood is virtually no insulation and virtually no insulation + a tiny bit of negligible insulation; neither one will insulate to any meaningful degree so I think it's moot from that end.

Can you use wainscoting instead of drywall?

Wainscoting uses mostly small pieces, so the scrap should work well. Actually, using drywall instead of wood for wainscoting has some advantages. In addition to the lower material and labor costs, drywall does not expand and contract as much as some woods do with changes in the humidity level.

How much does it cost to replace paneling with sheetrock?

The cost to install drywall is about $1.50 per square foot.
After material and labor are added in, the cost per panel can range from around $40.00 to $60.00. A typical 12x12 room, for example, will use 12 panels. This would put the cost at $480.00-$720.00.

Is wood paneling outdated?

Slide 1: Outdated Dark Wood Paneling
Today, while many homeowners have phased out the dark and dreary feature in favor of neutral or brightly painted drywall, paneling remains in plenty of homes that haven't been remodeled in decades. If, however, the walls are covered by sheets of wood-look panels, pull them off now!

Do you install beadboard over drywall?

Beadboard installs over drywall with panel adhesive. While the adhesive cures, use brads or nails to hold the panels in place temporarily.

How much is a sheet of beadboard?


Beadboard Paneling Cost per Square Foot
It costs $1 per square foot for real wooden beadboard. Imitation versions cost $0.50 to $0.75 per square foot. You will need caps and baseboards to finish off both types of paneling. These cost $0.30 to $2.50 per foot and are sold in 10-foot sections.

Is beadboard in style?

Beadboard is a traditional style of wall paneling that is made of evenly spaced interlocking tongue and groove wood elements. Today, it is installed as a decorative feature to walls, ceiling, cabinetry and even furniture to add an antique cottage look. It's also available in premade sheets or even wallpaper.

Do you have to glue beadboard?

No glue would be necessary. It is almost 3/4" thick so you will need to plan on a little edge trim to tame it down. BTW, unless you have installed perlins in the wall, the planks will run horizontally.

Do I need to prime beadboard?

Apply a coat of primer to the beadboard using a foam roller. Use a narrow paint brush to apply primer to all grooves in the paneling as well. If you're painting MDF beadboard, an oil-based primer is recommended because the wood fibers may absorb the water in latex paint, causing the beadboard to swell.

Does beadboard come in different widths?

Beadboard also varies in size and thickness. The common widths recommended in the past for good workmanship were 3" and 4" (showing 2 1/4" and 3 1/4" on the face). Nominal thickness ranged from 3/4" to 5/8" to 1/2" and as thin as 3/8" depending upon the manufacturer.

What kind of nails do you use for beadboard?


We recommend using a 2" 18 gauge finishing nail. At this point you can either use MDF glue and nails or just nails to hold up the boards. Using your compressed nail gun, nail up your first strip.

Do you hang shiplap over drywall?

You don't have to put your shiplap over drywall if there isn't existing drywall already in place. However, if you are simply remodeling a room, you can certainly put shiplap over existing drywall. Either option is relatively simple but requires a few different precautions mainly revolving around locating the studs.

Why do they call it shiplap?

Why Is It Called Shiplap? Early shipbuilding methods may have used a form a shiplap to construct the hull of a ship. The boards overlapping each other formed a watertight surface, which would make the vessel seaworthy. This could possibly be where the term shiplap originated.