How wide should pool steps be?

Asked By: Dorothea Dobberose | Last Updated: 30th January, 2020
Category: sports snooker and pool and billiards
4.1/5 (1,163 Views . 13 Votes)
The code states that the tread, or surface of the step, must be at least 10 inches wide from front to back. Rizzo finds 12 inches more comfortable, especially for those unsteady on their feet. Try to make the top step even wider.

Click to see full answer


Similarly, it is asked, how high should pool steps be?

Transfer steps must be 7 inches maximum height; 12 inches minimum and 17 inches maximum depth; and 22 inches minimum width. Transfer steps must be 8 inches maximum height; 14 inches minimum and 17 inches maximum depth; and 24 inches minimum width. One grab bar must be provided on each transfer step.

Beside above, can you use above ground pool steps in an inground pool? It is important to note that above ground pool steps and ladders cannot be used in an in-ground pool. They are designed to attach to the top rail of an above ground pool and/or a wooden deck only. For above ground pools without a deck, an A-frame ladder is used to provide access to and from the pool.

Also Know, how do you make a pool step by step?

15 Steps of Pool Building

  1. Step 1 – Permit, Engineering Plans & HOA (AVG 7-10 days)
  2. Step 2 – Layout (AVG 1 days)
  3. Step 3 – Excavation (AVG 1-2 days)
  4. Step 4 – Plumbing & Equipment Set (AVG 1-2 days)
  5. Step 5 – Structural Steel (AVG 1-2 days)
  6. Step 6 – Electric & Gas (AVG 1-2 days)
  7. Step 7 – City Electrical Inspection (AVG 2-5 days)

How much are inground pool steps?

I replaced the steps on two pool ladders. The original steps lasted many years but started to crack last year. and found them easy to install with no issues. (Out of the water).

Top Selected Products and Reviews.

List Price: $42.99
You Save: $2.10 (5%)

28 Related Question Answers Found

What height should a step be?

Standard Step Height
Researchers found that the ideal step height is 7.2 inches and the ideal step length should be anywhere between 11 and 12 inches.

How deep is an inground spa?

Most in-ground hot tubs will have a depth of 31 -inches in height, and a maximum of around 37 -inches. Because of safety issues, it's not recommended to go any deeper. Whether in-ground or above ground, all hot tubers need to use extreme caution so not to accidentally slip beneath the water.

How do you measure a handrail for a pool?

How to Measure Your Handrail
  1. Measure 6″ from water to 8″ – 12″ past last bend in handrail (See Figure 1).
  2. If bend is within 6″ of water, measure above bend.
  3. When measuring ladders, always measure 12″ – 24″ past last bend (See Figure 3.)
  4. When measuring spa handrails, measure only the gripping area (See Figure 4).

How do you build a small pool step by step?

How To Build A Swimming Pool:
  1. Keep your design simple. Keep the bespoke design features to a minimum.
  2. Go with a flat bottom.
  3. Box shapes are best.
  4. Avoid too many fittings.
  5. Don't go too deep.
  6. Move away from concrete or prefabricated pool walls.
  7. Use a well or borehole if you have one.
  8. Use a black liner.

How long does it take to make a pool?


As you might expect, gunite, or concrete, pools take the longest to build. On average, they will take from 45 to 75 days to be constructed according to Seasonal Pools. The primary reason gunite pools take substantially longer than other types of construction is that they need between 28 and 30 days to cure, or set.

What equipment is used to dig a pool?

To excavate your own pool you will need to rent a skid steer with a backhoe attachment, shovels, rakes, pick axe, sledgehammer, transit level, and a wheelbarrow. Make sure to have all of these items on hand while digging.

How do you build an inground concrete pool?

Part 2 Excavating the Pool's Base
  1. Measure and mark the pool's dimensions on the ground.
  2. Dig out the soil to create the basic shape of the pool.
  3. Level the pool's bottom and walls with a rake.
  4. Frame the pool with steel rebar and plywood boards.
  5. Install the plumbing lines underneath the rebar and plywood.

How do you make stone steps?

Lay stone block as you would for a patio. Dig down six to eight inches, the length and width of your landing. Build a form using 2 by 6 inch lumber and fill it in with gravel. Compact the gravel until level with the top edge of the form, then backfill form with sand and compact again.

What type of cement is used in swimming pools?

Concrete pools can be made of either shotcrete or gunite. The difference is when the concrete mixes with the water. Shotcrete refers to wet concrete that's already fully mixed before it's shot out of a hose. Gunite is dry concrete mix that only mixes with water at the nozzle when it's sprayed.

How do you pour a concrete pool?


The following steps will lay out how to pour a concrete pool that lives up to your vision without killing your budget:
  1. Step 1: Designate a Location. The first step in pouring your pool is deciding where to put it.
  2. Step 2: Excavate the Area.
  3. Step 3: Run the Plumbing and Build the Frame.
  4. Step 4: Pour the Concrete.

How do you build a budget pool?

Here are five ways to save money – whether it's a few hundred dollars or thousands.
  1. Choose Vinyl. Vinyl pools are markedly less expensive than either concrete or fiberglass – in terms of initial price tag, anyway.
  2. Go with a Smaller Pool.
  3. Use a Pool Kit.
  4. Install in the Fall.
  5. Cut Out the Extras.

How do I clean my inground pool steps?

How to Clean Inground Pool Steps
  1. Mix 1/2 gallon of vinegar with a gallon of hot water in a bucket.
  2. Use the scrub brush to apply the vinegar and water mixture to the steps, scrubbing lightly.
  3. Sprinkle baking soda on stains and let it sit.

What are inground pool steps made of?

Our inground swimming pool steps are vacuum molded from Luran, a state-of-the-art thermoplastic material that offers strength and durability superior to traditional steps made of vinyl-coated metal or acrylic and fiberglass.

How much does it cost to replace pool steps?

How Much Does It Cost to Install Pool Steps? The cost of pool steps varies, depending on the style and size of your steps. For a standard 6 foot walk-in staircase, the price will start at around $5,500. The average prices range from $4,500 to $6,500.

Do pools need coping?


If an inground swimming pool is constructed of concrete, it will need coping, which is a cap for the edge of the pool. If coping is installed correctly, any water that is splashed out of the pool should flow away from the pool and down into deck drains. Coping should be tilted slightly away from the pool.

How far can pump be from above ground pool?

Stay close to the pool.
Shorter pipe runs = less work for the pump which extends the life of the pump and uses less electricity. Our projects typically average a distance of 20–40 feet from the pool to the equipment, but as stated earlier, much longer runs are sometimes required.

What are the best above ground pool steps?

The 10 Best Above Ground Pool Ladders
  1. Confer 6000X. REVIEW. The sturdy Confer 6000X (around $117) has been designed to securely hold up to 300 pounds.
  2. A-Frame 7200. REVIEW.
  3. Blue Wave Easy. REVIEW.
  4. Access Step. REVIEW.
  5. Main Access Easy-Incline. REVIEW.
  6. Economy 635-52X. REVIEW.
  7. WaterDog Adventure. REVIEW.
  8. Intex Deluxe. REVIEW.