How much horsepower is a Honda gcv160?

Features

	GCV160	GCV190
Displacement	9.8 cu in (160 cm3)	11.4 cu in (187 cm3)
Net Power Output*	4.4 HP (3.3 kW) @ 3600 rpm	5.1HP (3.8 kW) @ 3600 rpm
Net Torque	6.9 lb-ft (9.4 Nm) @ 2500 rpm	8.3 lb-ft (11.3 Nm) @ 2500 rpm
PTO Shaft Rotation	Counterclockwise (from PTO shaft side)	Counterclockwise (from PTO shaft side)

In this regard, how much HP is 160cc?

The Honda 160cc lawnmower engine has a maximum speed of 3,300 rpm and can output 7.1 to 8.4 foot pounds of torque, depending on the exact configuration. Most 160cc Honda mower engines output around 5.5 horsepower.

Beside above, what is Honda GCV engine? The Honda 160cc GCV OHC Vertical Engine is a premium vertical shaft engine featuring Honda's latest overhead cam technology. Customers responsible for checking local codes and regulations.

Then, what kind of oil does a Honda gcv160 take?

These engines really are not picky about oil. I use whatever oil I have hanging around the garage in my GCV160. It's usually some 5w30 synthetic or 5w40 synthetic. I've used 10w30 conventional, 10w30 synthetic, and straight 30.

How do you start a Honda gcv160?

How to Start a GCV160 Honda Mower

Turn the fuel valve on the side of the engine 90 degrees counterclockwise to the "On" position.
Move the choke throttle lever, located on the left of the fuel valve, to the "Choke" position if starting from cold.
Shift the flywheel brake control above the throttle/choke lever to the "Run" position.

34 Related Question Answers Found

How many cc is a 10 hp engine?

The general rule is for every 15 CC there is 1 HP. For example, for a 150 CC engine you would take 150 divided by 15, which equals 10 HP.

How many cc is a 6.5 hp engine?

Technical Specs:

Name	6.5 HP (212cc) OHV Horizontal Shaft Gas Engine EPA
Certification	EPA
Diameter	70 mm
Engine displacement (cc)	212cc
Horsepower (hp)	6.5

How many horsepower is 400cc?

The Ninja 400 puts 43.4 hp to the ground at 9,900 rpm, backed up by 24.6 pound-feet of torque at 8,250 rpm. That's real-deal, rear-wheel horsepower, folks, and the new bike's curves tower over the outgoing 300's output.

How many cc is a 5 hp motor?

That is about 16.4cc Per horsepower.

How many cc is a 11 hp motor?

340 CC

How many cc is an 8 hp engine?

engine	cc	hp
Briggs & Stratton Industrial engine	480	16
Marine outboard	302	9.9
Briggs & Stratton Industrial engine	319	8
Briggs & Stratton Industrial engine	148	3.5

What is 547cc in horsepower?

547cc equals roughly 17 HP of power which considering the efficiency of the fuel injected single cylinder engine should be enough to run this 42″ mower.

What is 179cc in horsepower?

A powerful 179cc 4-cycle OHV Craftsman® engine kicks-out 5-6 HP, while eliminating the need to mess-around with fuel ratios, just gas it and get to work. Using less fuel than bigger machines, this snow thrower works hard while saving you money winter after winter.

What type of oil does a Honda lawn mower use?

SAE 10W-30

Can you use synthetic oil in a Honda lawn mower?

Honda engines are developed, tested and certified with petroleum based motor oils as a lubricant. Synthetic oils may be used; however, any motor oil used in our engines must meet all oil requirements as stated in the owner's manual. In addition, recommended oil change intervals must be followed.

What is the best oil for Honda lawn mower?

What is the best oil for a Honda 160cc OHC engine on a lawnmower? The owner's manual says to use 10W30 oil although 30 weight oil can also be used.

Can 10w30 be used instead of 5w30?

Can I Use 10w30 Instead of 5w30? The 10W30 and 5W30 both have different thicknesses in cold temperatures, and 10W30 is thicker than 5w30. So, it is best for vehicles running in cold climates to use the 5W30 since it is thinner than the 10w30.

What oil goes in Honda pressure washer?

Replace the drain plug. Refill the pump with DP70 pump oil if available. SAE 30W non-detergent oil will also work. Use only the quantity of oil specified in your pressure washer's owner's manual, as too much oil could cause leaks or damage to seals.

What is the difference between Honda GX and GC engines?

The main difference in the engines we use (GC160, GX120, GX160 and GX200) is that the GX engines are commercial duty while the GC160 is considered residential duty. On the GC motor, this makes for simpler operation, removing one step, but it has the drawback of not being able to run the fuel out of the carburetor.

Where are Honda small engines made?

Honda produces small engines at 5 production facilities worldwide. Our production capacity is well over 7 million units. Engines for the U.S. market are primarily sourced from the U.S., Japan, and Thailand.

Is synthetic oil OK for lawn mower?

Can you use synthetic lawn mower oil? Yes! We have modified our engine oil recommendations to state that you may now use a synthetic 5W30 (100074WEB) or 10W30 oil in all temperature ranges. We recommend the use of Briggs & Stratton Synthetic Oil.

How much compression should a Honda gcv160 have?

The Honda GCV160 engine has transistorized magneto ignition, horizontal type carburetor, and recoil or electric starter. Cylinder bore and piston stroke are 64.0 mm (2.5 in) and 50.0 mm (2.0 in), respectively. Compression ratio rating is 8.5:1.