How much does it cost to polish and seal concrete floors?

Well, the intensive surface repair ranges between $1 to $2 per square foot for grind and seal actual cost. If your contractor decides to resurface the concrete, be sure to pay $2 to $3 more per square foot as the cost to polish existing the concrete floors. Stamped concrete floors cost about $2 to $6 per square foot.

Click to see full answer

Accordingly, can you polish an existing concrete floor?

Almost any structurally sound concrete floor, whether new or old, can be polished. But there are some exceptions. For new floors, no special mix design is required to achieve good results. Existing floors typically require some surface preparation prior to polishing to remove dirt, grease, coatings, or blemishes.

Furthermore, what tools do you need to polish concrete? The most essential equipment required for a perfect concrete polished floor are:

Grinders and Polishers:
Diamond Tools for Grinding and Polishing:
Industrial Floor Vacuum:
Hardening and Compacting Agents:
Enhancing the Floor with Coloring Agents, Dyes and Stains:

Similarly, it is asked, is it expensive to polish concrete?

The cost of polished concrete can be as little as $25 per square metre, but on average, grind and seal polished concrete will cost around $50 per square metre. Honed concrete may cost $75 per square metre. Mechanically polished floors may cost $100 or more per square metre.

What does vinegar do to concrete?

Vinegar: The Good, Bad and Downright Ugly Truth as a Cleaning Agent. Etching – Vinegar's ability to dissolve CaCO3 will dull your marble, travertine, concrete and terrazzo surfaces. It may “clean” the surface but it is also dissolving pits into the finish and effectively dulling it.

24 Related Question Answers Found

What is the best finish for concrete floors?

Top Concrete Finishing Options

Acid Stain. An acid stain for concrete floor has a very bold look, recognizable by its mottled appearance and highly variegated finish.
Water-Based Stain.
Fast Stain.
Acrylic Sealer.
Standard Epoxy.
Metallic Epoxy.
Terrazzo or Granite Epoxy.
Quartz Sand Epoxy.

How can I make my concrete floor shine again?

Add shine to your stained concrete floors.

Sweep your floor. Use a dustmop to avoid damaging the surface of your stained concrete floor.
Mop your floors. Use a damp mop for occasional cleanup.
Seal your floors.
Wax your floors.
Avoid scuffing your floor.
Maintain your shiny floors.

How long does it take to polish concrete?

2 to 3 days

How much does it cost to polish concrete floors?

Polished Concrete Cost

Economical: You can expect to pay between $3 and $12 per square foot for polished concrete, depending on your location and the complexity of the project.

Can you buff concrete sealer?

Buffing in CDP Smooth Floor concrete sealer. Buffing in CDP Smooth Floor will give you a 20 year finish that will not flake, chip, or peel off. This will enable easier sweeping and cleaning of you concrete floor. This process can be done on colored concrete as well.

How do you hand polish concrete?

How to Hand Finish a Concrete Countertop

Fasten a hook-and-loop 50-grit polishing pad to a variable speed hand polisher.
Switch to a 100-grit pad on the polisher.
Clean the countertop surface with a mixture of 1/4 to 1/2 cup vinegar mixed in a gallon of water.
Apply a concrete sealer to the countertop.
Things You Will Need.
Tips.
Warning.
References (3)

Can you polish concrete yourself?

First, you will start by polishing the floor using a coarse grit abrasive disc. This will help remove any surface stains or rough areas on the floor. When polishing the floors, it is important to make sure you are using proper technique, which will be used for all steps involving a concrete polisher.

Is polished concrete cheaper than tiles?

Compare that to polished concrete look floor tiles, which cost a fraction of the price at TFO. Even including the cost of installation, it would be much cheaper to use concrete look tiles.

How do you restore a concrete floor?

Saturate the concrete with water and then use a broom to push out any puddles from the pitted areas or low spots. The concrete should be damp when you apply the resurfacer, but not wet to the touch. Pour the mix into a puddle on the slab and immediately spread it (Photo 7).

Can you polish self Levelling compound?

Polishing Self-leveling Concrete (Param 6000)

Using a polishable self-leveling concrete overlay is an excellent option for creating a high-shine polished concrete floor. Polishing self-leveling concrete overlays normally does not require the addition of another layer of product other than a protective top coat.

Do polished concrete floors scratch easily?

Polished concrete flooring is extremely strong and resilient and is able to withstand the pressure from very heavy foot traffic and equipment. It is very difficult to damage and is nearly impossible to chip or scratch.

Is polished concrete slippery?

Polished concrete is NOT slippery when dry

When kept clean, polished concrete has about as much grip as regular concrete, and provides better foot traction than marble or even some linoleum surfaces.

How much is a concrete floor?

Concrete flooring cost ranges between: $2 to $6 per square foot for a basic design. $7 to $14 for a mid-range design. $15 to $30 for a high-end, customized floor.

Can you do polished concrete over tiles?

Concrete Resurfacing with a Polished Concrete Overlay can transform an old worn out concrete floor into a stunning individual designed floor. Colour can be added or even a mixture of colour can be used. Polished Concrete Overlays can be placed over any sound floor, concrete, timber, tiles or cement sheeting.

What is Microtopping?

Microtopping is an alternative concrete-type service offered by P Mac. You can use it on wood, concrete, self-levelling, ceramic, natural stone, or any other type of surface. It is the ideal option for those who want a continuous, innovative and tactile surface to create a unique and modern space.

How much is polished concrete per m2?

Concrete polishing can cost from $50 - $100 per square metre, depending on the method used. To begin, basic polishing starts at an average cost of $50 per square metre for the grind and seal method. The honed polishing method is on average around $75 per square metre.