How many roof tiles should be nailed?

Asked By: Malick Sussenberger | Last Updated: 6th April, 2020
Category: style and fashion nail care
5/5 (847 Views . 14 Votes)
Double-lap tiles
For nibless tiles, two nails should be used to secure each tile. For nibbed tiles at roof pitches below 60°, two nails should be used to secure each tile in at least every fifth course.

Click to see full answer


Similarly, do roof tiles need to be nailed down?

It is not necessary to nail every single tile to the battens. Every tile of the two rows at the eaves, those up the verges, and along the two rows of the ridge should be nailed, but beyond that it is only necessary to nail every fifth tile horizontally and every third tile as you move up the roof.

Also Know, how many roof tiles do I need per m2?

Tile Range Tile Size 35° – 89° Tile Qty
Concrete Plain Roof Tiles 266 x 165mm 60 tiles/m2
Clay Rosemary Craftsman Tiles 265 x 165mm 60 tiles/m2

Consequently, should roof tiles be nailed down UK?

Fixing. Aluminium nails should be used in preference to galvanised nails as aluminium will not corrode whereas the galvanise coating will tend to. Every tile along the eaves, up verges and along the ridge should be nailed, but otherwise only nail every fifth tile horizontally, and every third tile up the roof.

What nails do you use for roof tiles?

Stainless steel nails are also good for fastening tiles and slate, or you can work with copper nails for standard roofing purposes. Galvanized roofing nails are steel nails that are zinc-coated. They hold up better against rust, and they can also be used for asphalt shingles.

37 Related Question Answers Found

How much should Roof tiles overlap?

This is normally specified with the tile manufacturer and it's advisable to check how much they say a roof tile should overlap, normally on a smooth faced tile the overlap is 75mm (3″) and on granular or sandfaced tiles its 100mm (4″) however if the roof is shallow pitched, is facing a windy direction or will be prone

Can you walk on a tile roof?

First off, we don't recommend that you walk on your concrete tile roof, if you can avoid it. Sure, concrete tiles are strong. But they're not really made to be walked on. Every time you walk on the tiles, you put stress on them that can crack them or loosen them.

How do you nail roof tiles?

Tiles can be nailed either directly into the roof sheathing or tiles with lugs can be nailed to battens. Corrosion-resistant nails must be minimum 11 gauge, with 5/16 -inch heads, and long enough to penetrate the sheathing by 3/4 inch—typically 8d nails.

How do you repair roof tiles?

Cracked or Broken Roof Tile
  1. Carefully pry up the tile (or tiles) just above the cracked or broken one.
  2. Break the faulty tile, and remove the pieces.
  3. Spread a small amount of roofing cement along the underside of the replacement, and slide it into place.
  4. Press all tiles down gently but snugly.

Do tile roofs need to be replaced?


Tile roofs installed with base flashings only, where gaps exist or cement was used to fill them, can expect to be replaced between years 15 and 25. Roofs with top flashings only will likely last 40-50 years.

What are the best type of roof tiles?

Interlocking Roof Tiles
Concrete is by far the most common material used for this particular style, although they can be purchased in clay and slate. For roofs that require a low pitch, the Sandtoft Standard pattern interlocking tile is both easy to install and highly durable.

Should roof tiles move in the wind?

It can be tough to inspect for lifted tiles from the ground, but you should notice a certain looseness when you handle them from the roof itself. Tiles can curl in the wind when they are hit from the side.

How much does it cost to replace a broken roof tile?

Labor: According to lyonsroofing.com, the average cost for the removal and replacement of tiles ranges from $300 to $450 per square. This is excluding the use of new tiles and applies to all materials including clay, concrete, aluminum or steel. Alternatively, roofers may charge between $45 and $75 per hour.

Will a missing roof tile cause a leak?

Whether it's one, or many, missing tiles that is leaving your roof vulnerable to the outside elements, missing roof tiles will cause roof leaks. Although the open patch of roof may be small, an average amount of rainfall is enough to cause extensive damage to other areas of your home.

What does mechanically fixed mean?


Well, as simple as it sounds, a mechanically fixed single ply roof system is a roof system that is held in place using mechanical fastenings. These secure the single ply membrane, over the top of the insulation and vapour control layer, and are fastened in place to the roof deck.

What is a single lap roof tile?

Single lap tiling
Most single lap tiles have a tongue-and-groove joint along the side edges to form a series of interlocking joints. There is a reduction in weight of the overall roof covering compared to double lap tiling, but the batton size will be larger.

How do I calculate how many roof tiles I need?

When setting out the measure a roof's area to calculate the materials that will be required, the following three steps are essential:
  1. Measure the Pitch or Angle of the roof slope.
  2. Work out the Rafter or Hip / Valley length.
  3. Measure the Span (building width) or Run (half building width)

How many roof tiles are in a square?


Well a square is 100 square feet. On average there are about 3- 4 bundles in a square. If there are three bundles per square each shingle is 12 inches by 36 inches and there are about 29 shingles in a bundle. So id say there are about 87 roof tiles/shingles in a roofing square.

How many 300x300 tiles are in a m2?

How Many 300 x 300 tiles in a square metre (m2)? The quantity of 300 x 300 tiles in a square meter (m2) equals 12 tiles.

How much is tiling per m2?

Tiling costs per square metre range from $30 to $120. Average prices for laying tiles are between $45 and $50 per square metre.