How many channels does Dante support?

Asked By: Viva Pendas | Last Updated: 4th March, 2020
Category: technology and computing digital audio
4.3/5 (79 Views . 14 Votes)
Dante Via supports 2×2 channels (2 in and 2 out) for software applications, 32×32 channels for hardware devices, and a total of 48 source channels and 48 destination channels.

Click to see full answer


Also to know is, do all Dante devices have a secondary network capability?

A computer running Dante Via [can] be the Clock Master for a Dante network. [All] Dante devices have a secondary network capability. All Dante devices except Ultimo-based (low channel count) devices can route audio to themselves.

Subsequently, question is, what is Dante protocol? Dante is a combination of software, hardware, and network protocols that delivers uncompressed, multi-channel, low-latency digital audio over a standard Ethernet network using Layer 3 IP packets. Dante is an acronym for Digital audio network through ethernet.

In this way, how does Dante network work?

In a Dante-enabled device, the hardware takes digital audio and 'packetizes' it. Basically, it segments the audio and wraps it in IP (Internet Protocol) packets suitable for transmission across an Ethernet network.

What sample rates are supported by Dante?

Supported Audio Formats

  • 44.1 kHz.
  • 48 kHz.
  • 88.2 kHz.
  • 96 kHz.
  • 176.4 kHz.
  • 192 kHz.

33 Related Question Answers Found

Is Dante multicast?

Dante configures routing with unicast by default, and multicast will not be required for most of small-to-mid scale Dante systems. To understand when the multicast settings of a switch need to be configured, it's first necessary to understand multicast and "flows".

Does Dante require special network cabling?

Does Dante require any special network infrastructure? No, special network infrastructure is not required. Since Dante is based upon universally accepted networking standards, Dante-enabled devices can be connected using inexpensive off-the-shelf Ethernet switches and cabling.

When should QoS be considered?

QoS is required when using Dante in networks that have 100Mbps devices and is optional in networks with Gigabit devices. We recommend that QoS be enabled in all Dante networks in order to ensure proper operation under all possible conditions. See this FAQ for information about DSCP/Diffserv values.

How is a Dante clock master selected?

How is the Master Clock determined? Dante uses a distributed Master Clock election protocol that automatically selects the best clock for the network, based upon information advertised by each Dante device.

Does Dante support MIDI?


Dante Controller is not required to be present for a Dante network to work. Dante only transports audio data, and does not interfere with MIDI. The names of devices and channels in Dante are: User-definable and remembered by devices.

Do Dante devices require special IP configuration?

However, by default, Dante devices obtain IP addresses automatically – so there should be no need to specify static IP addresses, unless it is a specific requirement for your network.

How does Dante interact with Energy Efficient Ethernet EEE switches?

EEE (Energy Efficient Ethernet) is a technology that reduces switch power consumption during periods of low network traffic. This may cause EEE to be enabled in Dante networks when it is not appropriate, resulting in poor synchronisation performance and occasional dropouts.

What is the difference between aes67 and Dante?

The biggest differences between these two systems are that Dante is proprietary and operates on layer 3 of the OSI 7 layer model. AVB is an open set of standards and it operates on Layer 2. While AVB is a fantastic technology, it is broad in scope and its future definitely lies in more areas than just pro audio.

Does Ethernet carry audio?


In audio and broadcast engineering, Audio over Ethernet (sometimes AoE—not to be confused with ATA over Ethernet) is the use of an Ethernet-based network to distribute real-time digital audio. Because of the fidelity and latency constraints, AoE systems generally do not utilize audio data compression.

What ports does Dante use?

Internal
Protocol Port Usage
UDP 8001 Dante Millau Device Proxy (Internal only)
UDP 8002 Dante Lock Server
UDP 8751 Dante Controller metering port (From FPGA based devices)
UDP 8800 Control & Monitoring (Excluding DVS-4.0 and Via)

How do I get Dante certified?

Dante Certification Level 1 - Introduction to Dante
To get certified for Level 1, you must complete the Level 1 course & exam at audinate.com/certify, which includes a one-hour video course. (Note: If you attend an in-person Level 1 Dante training course, you may skip to the exam.)

What does the Dante clock master do?

Dante clocking guarantees that all devices are synchronized to within 1 microsecond or less, and that all devices can play out audio at the level of sample accuracy.

What do you mean by Ethernet?

Ethernet is a way of connecting computers together in a local area network or LAN. It has been the most widely used method of linking computers together in LANs since the 1990s. The basic idea of its design is that multiple computers have access to it and can send data at any time.

What is LAN connection?


LAN. Stands for "Local Area Network" and is pronounced "lan." A LAN is a network of connected devices that exist within a specific location. A LAN may be wired, wireless, or a combination of the two. A standard wired LAN uses Ethernet to connect devices together. Wireless LANs are typically created using a Wi-Fi signal

What is aes50?

AES50 is an Audio Engineering Society open standard defining the bidirectional. transmission of multichannel digital audio over 100 Mbit/s CAT 5/5e cable. AES50-2005. AES standard for digital audio engineering – High resolution multi-channel audio interconnection (HRMAI).

How are device names used in Dante?

In Dante, devices and audio channels are identified by names and labels, not 'magic numbers'. Dante routing is performed using the device names and channel labels. A receive channel can be subscribed to the name of a transmit channel at a device.