How many amps does a car cooling fan use?

Category: home and garden indoor environmental quality
4.4/5 (3,436 Views . 16 Votes)
28 amps



In this regard, how many amps does a fan use?

One amp drawn by a ceiling fan is equivalent to about 120 watts. Low settings use less amperage while higher settings use more. For example, an average ceiling fan set on low speed uses about 0.25 amp, on medium speed about 0.4 amp, and on high speed about 0.6 amp.

Also, what will 10 amps run? 10 amps indicates how much you can use at once. 10 amps is a good supply and will run pretty much everything except a domestic microwave. It is not enough to run everything at once though. for example, if you use a domestic electric kettle and a heater together it may trip out.

Likewise, how do you wire a radiator fan to stay on?

How to Straight Wire a Cooling Fan to an Engine

  1. Locate the positive and negative wires on the cooling fan. Cut both wires and strip 1/2 an inch of insulation off of the ends of the two fan wires.
  2. Connect one end of the 12-gauge jumper wire to the black ground wire of the fan. Connect the other end of that wire to the engine block or any metal part of the car body.

Do fans use a lot of power?

Energy Costs of Fans Fans, in general, do not consume a lot of energy. A DC fan – as opposed to an AC fan running directly on the 110-volt alternating current coming out of your wall outlet – is extremely efficient and commonly uses less than a third of the energy consumed by the older AC fans.

39 Related Question Answers Found

How many watts is 10 amps?

Equivalent Watts and Amps at 12V DC
Power Current Voltage
90 Watts 7.5 Amps 12 Volts
100 Watts 8.333 Amps 12 Volts
110 Watts 9.167 Amps 12 Volts
120 Watts 10 Amps 12 Volts

How many ceiling fans can be on a 15 amp circuit?

1 Answer. There should be no problem running 4 ceiling fans on a single 15 ampere circuit, though it will depend on what else is on the circuit. Say a 52" fan is 90-100 watts (at high speed), plus three 60 watt bulbs. That puts each fixture at 280 watts or so.

How many watts is 8 amps?

Watts and amps conversions at 120V (AC)
Power Current Voltage
800 watts 6.667 amps 120 volts
900 watts 7.5 amps 120 volts
1000 watts 8.333 amps 120 volts
1100 watts 9.167 amps 120 volts

How many outlets can be on a 15 amp breaker?

As a rule of thumb in counting devices on a circuit you count each outlet (light or receptacle) as 1.5 amps. Now remember you only count 80% of the rating which means a 15 amp breaker should not exceed 12 amp load, a 20 amp breaker would be 16 amps.

How many amps does a 200 watt LED light draw?

It depends on what voltage you connect it. It is rated to be 200 Watt for a 120 V supply. therefore R = 72 Ohms. I = 1.67 Amps.

How many amps does an electric cooling fan draw?

Twelve- to 16-inch fans can draw from 15 to 28 amps, while some dual fan applications can draw up to 35 amps.

Do I need a relay for electric fan?

You need to use a relay on any high draw component..Especially Fan motors, and TWO in parallel are preferred as a Safety Issue. A Relay Coil (Or Set of coils) Will only draw an amp to an amp in a half, Whereas The motor will draw 17 amps and Spike on startup, or If you Suffer a rotor lock on the motor..

How do I know how many amps my compressor is?

According to Underwriters Laboratories, divide the MCC by 1.56 to determine the Rated load Amperage (RLA). Often, compressor manufacturers will divide the MCC by 1.44 to determine the RLA of their compressors to meet certain other protection specifications. Compressor Amperage Data.

How do you determine the amperage of a motor?

Divide the watts of a given electrical item by the total number of volts available from the electric outlet to calculate amperage draw. The amount of current flowing through the wire is measured in amperes, or amps. The equivalent of available electricity at the power source is voltage, or volts.

What causes a motor to draw high amps?

The most common causes of high no-load current after a motor is rewound are incorrect winding data and stator core damage. Incorrect winding data that increases the magnetic flux levels as compared with design levels will result in increased no-load current.

What is FLA and RLA?

RLA - "Running Load Amps" - current drawn during normal operation of electric motor. FLA - "Full Load Amps" - amount of current drawn when full-load torque and horsepower is reached for the motor. FLA is usually determined in laboratory tests.

How can you tell if a fan relay is bad?

Symptoms of a Bad or Failing Cooling Fan Relay
  1. Engine running hot. One of the first symptoms commonly associated with a bad or failing cooling fan relay is an engine that runs hot or overheats.
  2. Cooling fans do not function. Non-functional cooling fans are another common symptom of a potential problem with the cooling fan relay.
  3. Cooling fans stay on at all times.

How much is a cooling fan relay?

So, when the cooling fan relay stops working, the coolant can get too hot, and the car can overheat. To get your cooling fan relay replaced, you will pay, on average, $80-$160, depending on the type of car you have and the mechanic's fees. The labor should cost around $70, while parts should run you $10-$50.

When should radiator fan come on?

To check the temperature at which the fan comes on, turn the A/C off and keep the engine running until it reaches normal operating temperature. Most fans should come on when the coolant reaches about 200 to 230 degrees. If the fan does not come on, something in the control circuit is defective.

How do you wire a fan?

  1. Connect the green/copper wires together.
  2. Connect white wires together.
  3. Connect black wires together.
  4. Connect the lighting wire, typically blue, to the black fan wire and the black ceiling wire.
  5. Tuck the wires back into the box.
  6. Turn the power back on and test the fan.