How do you reset the gas valve on a furnace?

Locate the gas switch or control knob and move it to the "off" position. Wait a full five minutes. Turn the gas control knob or switch back into the "on" position after the five minutes pass. Replace both panel doors to the central heater.

Hereof, how do you turn on the gas valve on a furnace?

Re-lighting your pilot flame

Make sure the gas valve is turned on (lever should be parallel to the pipe)
Turn the furnace dial to “pilot” position.
Press and hold the thermocouple bypass button (otherwise no gas will flow since the thermocouple will detect that there is no pilot flame).

Similarly, how much does it cost to replace a gas valve on a furnace? Furnace Gas Valve Replacement Costs A furnace gas valve costs anywhere from $200 to $600 to replace. This part allows natural gas or propane to flow to your unit.

Keeping this in view, can a furnace gas valve be repaired?

Furnace gas valves occasionally stop opening and closing properly with age. Sometimes cleaning or repairing them can restore their operation, but when that doesn't work, replacement is the only option. Gas valves aren't repaired often because the labor cost would push the price past the cost of a new part.

Why do gas valves fail?

A diaphragm connected to a valve controls gas flow and pressure. A thermocouple senses heat from a pilot flame and generates a current that holds open a solenoid valve. Gas valves can fail from a variety of causes including contamina- tion, product deficiency, and misuse.

26 Related Question Answers Found

What does a gas valve look like?

Houses with natural gas have a main shutoff valve (Fig. A) located just before the gas meter. This valve, often called the street-side valve, is normally a rectangular nub (Photo 1). When the long side of the nub or handle is parallel to the incoming gas line, it's open and the gas is flowing.

Why is my furnace not getting gas?

Check Your Air Filters

Often times the reason air does not get to your furnace's igniter is because it is restricted. The main reason for this air restriction is usually traced back to dirty air filters. So check them if your gas furnace fails to ignite when you turn the system on.

How does a gas valve work on a furnace?

A furnace gas valve is a component of your furnace's fuel system. The furnace gas valve opens and closes, which allows the flow of gas to the pilot light and burner(s). While the component itself if actually rather simple, a furnace gas valve is a crucial part of your HVAC system.

What is the gas valve on a furnace?

The gas valve on your furnace is one of the most important parts. It is ultimately responsible for delivering an adjusting the flow of gas pressure to your furnace to keep it lit when running. A gas valve replacement is a common furnace repair in older furnaces.

How do I free a stuck gas valve?

With the pump running and AFTER you've heard the 'click' from the solenoid' GENTLY tap the body of the gas valve just a couple of times with a soft hammer or piece of wood. This MAY free the valve if it's stuck.

How do you test a thermocouple?

Steps

Locate the pilot light controls on the gas valve.
Turn the pilot light on for 30 seconds.
Release the button to see if the pilot light goes out.
Turn off the gas supply to test the thermocouple again.
Count to 20 and wait for the pilot light to go out.
Listen for clicking near the gas valve.

What does a gas valve do?

A gas control valve can be found on any appliance that utilizes gas. These valves are vital for the operation and safety of any gas appliance. The valve does exactly what it sounds like, it controls the amount of gas flowing to create a steady flow without allowing any gas to leak.

How do you test a gas regulator?

Connect the hose on the positive line on the manometer to the regulator inlet located beneath the removed cap. Turn the gas shutoff valve counterclockwise to turn the gas on, and check the display on the manometer.

Why is the gas valve on my furnace buzzing?

The buzzing sound can also be caused by low voltage issue to the gas valve. There may be enough voltage present to open the gas valve but not enough to make the solenoid fully travel and hang up. Tapping the valve may assist the solenoid to finish travel. Check for voltage at the gas valve.

How much is a Honeywell gas valve?

Just remember to check for gas leaks at all connections. You can do this! In Stock. Only 1 left in stock - order soon.

Top Selected Products and Reviews.

List Price:	$89.11
Price:	$79.95
You Save:	$9.16 (10%)