How do you reset a Tiger River Spa?

The unit should stop operating and the GFCI power indicator will go out. Wait 30 seconds and then reset the GFCI by pushing the RESET button. The GFCI power indicator will turn on, restoring power to the spa.

Just so, how do you turn on a tiger river hot tub?

How to Unlock Tiger River Spa Controls

Tap the "MODE ^" button until "TOOLS" appears on the screen.
Tap "MODE ^" until "SPA -" is shown on the display.
Press "OFF V." Use the spa controls as normal.
Tap the "MODE ^" button until "TOOLS" appears on the screen.
Tap "MODE ^" until "LOCK -" is shown on the display.
Press "OFF V." Adjust temperature as normal.

Also Know, who makes Tiger River spas? Tiger River spas are from Watkins Manufacturing, maker of Hot Spring® spas, the world's number one selling brand.

Also, where is the reset button on my hot tub?

How to Reset a Spa Heater

Locate the spa's high-limit reset. This is a red button found on many spa packs.
Press the high-limit reset button.
Turn on your spa and observe its operation.
Flip the breaker panel switch on or press the reset button on the GFCI outlet to restore power.

How do you turn on a hot spring portable spa?

To turn on the spa light, press the LIGHT plus (+) button. The light will turn on at maximum intensity and the light symbol will illuminate on the control panel display. To reduce the intensity of the light, press the LIGHT minus (-) button.

35 Related Question Answers Found

Why does my hot tub have no power?

Faulty Wiring

This will often cause a breaker to trip or a fuse to blow, but not always. If it's the wires carrying power into or out of the transformer, you can have a no power situation. Shut off all power before touching or replacing any damaged spa wiring.

How do I know if my heating element is bad in my hot tub?

Find a replacement heater element. If your breaker is not tripping but your hot tub still isn't heating, testing voltage to the heater using a multi-meter will help determine the cause. With the spa on, test both of the leads on the element at the same time. If the meter is reading 240v, the element is the problem.

Do hot tubs run all the time?

It's recommended to do this every 3 months or so to keep the water in the best condition and to keep the hot tub in as fresh and clean condition as possible. You might also have a period of time when you know that you are going to be away or definitely won't be using the hot tub.

How do you fix the error code on a hot tub?

My Hot Tub Is Displaying FLO or DR. or DRY Error Message

FLO, DR. or DRY errors commonly occur due to debris and blockages.
If your tub is displaying this message it simply means that there is an issue with water flow.
The first thing you should do is check your tub's water level.

Can you test a hot tub without water?

Hot Tub Running without Water. You did not say what spa you have, so it's hard to tell if any damage was done. Most spas have an over-temperature sensor that turns them off if the heater is on but the circulator pump is not running, but this relies on the spa being filled with water. This means no water flow no heat.

Is there a reset button on a Jacuzzi bathtub?

You will find a reset button typically on the heater unit. Usually there is a pilot light. When you're ready to reset, push the button. Some spa units have a high limit switch which will turn off the spa heater if the thermometer fails.

What does EC mean in hot tubs?

Ecn or Ec is Alternating with Temp: The Spa is Operating in the "Economy" (Ecn or Ec) Heating Mode. The Water Temperature will probably drop Below Set Temperature between Filter Cycles. Other Heating Modes are Standard, Standard in Economy, and Sleep Modes.

What is SL mode on hot tub?

While your hot tub is in sleep mode (or 'SL' & SLP mode on some models), the jets will operate occasionally to filter the water. In sleep mode, your hot tub's heater will usually only kick on once the temperature dips below 20 degrees of the set temperature.

How do you change the mode on Balboa spa?

Balboa Controller VS500Z and VS501Z Mode Settings for Standard, Economy and Sleep. Mode is changed by pressing the Temp or Set button, and then pressing the Light button. If there are UP and DOWN buttons, use the UP button. Do not press the buttons at the same time.

What mode should my hot tub be in?

Note: Economy mode should only be used if you are not planning on using the hot tub for two or more days, any less than that and it is more efficient to keep it at a set temperature. You can instead lower the set temperature by 2 degrees.

How long does it take to heat a hot tub?

approximately 4 hours

How do you heat a Balboa hot tub?

High Range can be set between 26.5°C to 40°C. Low Range can be set between 10°C to 36°C. To change the range press the temp/warm button followed by the light button, then press temp/warm button again. To exit, press the light button or wait for 10 seconds to go back to the Main Screen.

How do you adjust the temperature on a Marquis Spa?

To Change the Set Temperature Factory default temperature setting: 102°F (39°C). The LCD window displays the actual water temperature. Press the TEMP+ or the TEMP- pad. Each pad press changes the set temperature by one degree.

What does the safety suction light mean on a Cal Spa?

Posted March 1, 2013. Regarding the Safety Suction light, we have a different model Cal Spas and have the light on all the time. The dealer explained that this indicates that the feature is enabled and the light should normally be on. We have it on all the time.

Why won't my bathtub jets work?

If the jetted tub will not turn on or the pumps will not start at all, turn off the tub. Make sure the tub is connected to a power supply, that power in the room is not out and that you have completely depressed the "On" button for the jets. If there is no voltage, the pump is not connected to the power supply.

Do Jets need to be on to heat/hot tub?

Heating your spa, with the spa cover on, will raise the water temperature at a faster rate than heating without the spa cover. Do not run the jets when your spa is either heating up or is not in use: The air generated from the jets cools the temperature in the water.

How do I clean the jets in my hot tub?

Fill the tub with hot water to at least three inches above the height of the jets. Add two to four teaspoons of powdered dishwasher detergent (or another low-foaming disinfectant). For a deep clean, you can also add up to one-half cup of bleach. Run the jets for 15 minutes, and then turn off and drain the bathtub.