How do you make a back to back Stemplot?

Asked By: Tiffaney Parente | Last Updated: 12th June, 2020
Category: sports horse racing
4.8/5 (503 Views . 31 Votes)
To create a back to back stem-and-leaf plot, we do the same thing on the left side of the plot using Set 1 data. Again, and this can be a little tricky at first, the leaf numbers go in order with the smallest being closest to the stem and getting larger as you move out further to the left.

Click to see full answer


Similarly, you may ask, what is the purpose of a back to back Stemplot?

A back-to-back stemplot is used for numerical data, where two sets of data use the same set of stems, but one data set radiates to the left and the other radiates to the right.

Secondly, what does a back to back stem and leaf plot tell you? Stem-and-leaf plots are an effective way to present data, allowing us to see at a glance the distribution of numbers. A back to back stem-and-leaf plot goes one step further and allows for easy comparison of two sets of numbers.

Keeping this in consideration, how do you do a back to back stem and leaf plot in Excel?

To create a stem and leaf plot:

  1. Click on the QI Macros menu, then Chart Templates, then Stem and Leaf Plot to open the template.
  2. Input or cut and paste your data into the yellow input areas.
  3. Double click on the button and QI Macros will perform the analysis and create the two-sided plot.

What is a back to back stem and leaf diagram?

Back-to-Back. Stem-and-Leaf Plots. Introduction. This procedure generates a stem-and-leaf plot of a batch of data. The stem-and-leaf plot is similar to a histogram and its main purpose is to show the data distribution while retaining the uniqueness of each data value.

36 Related Question Answers Found

When would you use a stem plot?

They are typically used when there is a medium amount of quantitative variables to analyze; Stemplots of more than 50 observations are unusual. The name “Stem plot” comes because there is one “stem” with the largest place-value digits to the left (shaded in gray in the image below) and one “leaf” to the right.

When would you use a histogram?

The major difference is that a histogram is only used to plot the frequency of score occurrences in a continuous data set that has been divided into classes, called bins. Bar charts, on the other hand, can be used for a great deal of other types of variables including ordinal and nominal data sets.

What type of data can be displayed in a scatter plot?

A scatter plot (aka scatter chart, scatter graph) uses dots to represent values for two different numeric variables. The position of each dot on the horizontal and vertical axis indicates values for an individual data point. Scatter plots are used to observe relationships between variables.

What is a five number summary in statistics?

Five Number Summary. The "five number summary", or five statistical summary", consists of. (1) the minimum, (2) the maximum, (3) the median, (4) the first quartile. and (5) the third quartile. Find the "five number summary" for the data set.

What is a split Stemplot?


A Split Stem and Leaf Plot takes an ordinary stem and leaf plot and “splits” the stem section into two entries. This way, instead of having many numbers in one leaf section, it is split into two separate categories.

Why do you split stems on a Stemplot?

Splitting the stems. The organization of this stem and leaf plot does not give much information about the data. With only one stem, the leaves are overcrowded. If the leaves become too crowded, then it might be useful to split each stem into two or more components.

How do you make a box and whisker plot on Excel 2013?

Beautiful Box Plots in Excel 2013
  1. Step 1: Calculate Quartiles and Extremes. Create another table with the following rows for each series: min, q1, q2, q3, max.
  2. Step 2: Calculate box and whisker edges.
  3. Step 3: Create a stacked column chart.
  4. Step 4: Make the chart look like a Box Plot.
  5. Step 5: Add Whiskers.

Where is QI Macros menu in Excel?

PC Installation Instructions
  • Close Excel.
  • Right-click the .
  • Next, double-click the QI Macros setup.exe file to run the installation wizard.
  • Answer the prompts.
  • Open Excel, you should now see "QI Macros" on your menu bar.

How do you draw a histogram in Excel?

Create a histogram chart
  1. Select your data. (This is a typical example of data for a histogram.)
  2. Click Insert > Chart.
  3. In the Insert Chart dialog box, under All Charts, click Histogram , and click OK.

How do you make a box and whisker plot on word?


Create a box and whisker chart
  1. Select your data—either a single data series, or multiple data series. (The data shown in the following illustration is a portion of the data used to create the sample chart shown above.)
  2. On the ribbon, click the Insert tab, and then click. (the Statistical chart icon), and select Box and Whisker.

How do you make a box and whisker plot on Excel?

Create Your Microsoft Excel Box and Whisker Plot
  1. Select your data.
  2. Click the Insert.
  3. In the Chart section in the ribbon, click Insert Statistical Chart and select Box and Whisker.

How do you calculate quartiles in Excel?

Click on cell "B2" and enter the following formula, without quotes: "=QUARTILE. EXC(A:A,1)". This will give you the first quartile. Enter the same formula into cell "B3," except change "1" to "2" and you will get the second quartile, or median.

How do you make a box and whisker plot online?

Online Box Plot Generator
  1. Enter your data in the text box. You must enter at least 4 values to build the box plot. Individual values may be entered on separate lines or separated by commas, tabs or spaces.
  2. Press the "Submit Data" button to create the plot.

How do you find the key in a stem and leaf plot?

The stem-and-leaf plot only looks at the last digit (for the leaves) and all the digits before (for the stem). So I'll have to put a "key" or "legend" on this plot to show what I mean by the numbers in this plot. The ones digits will be the stem values, and the tenths will be the leaves.

What does a box plot show?


A boxplot is a standardized way of displaying the distribution of data based on a five number summary (“minimum”, first quartile (Q1), median, third quartile (Q3), and “maximum”). It can tell you about your outliers and what their values are.

What is a two sided stem and leaf plot?

Double stem and leaf plots are used to compare two distributions side-by-side. This type of double stem and leaf plot contains three columns, each separated by a vertical line. The center column contains the stems. The first and third columns each contain the leaves of a different distribution.

What is a side by side stem and leaf plot?

two-sided stem-and-leaf plots. Two-sided stem-and-leaf plots are two stem-and-leaf plots plotted side by side and are often called back-to-back stem-and-leaf plots.