How do you clear the codes on a Maytag Bravos washer?

VIDEO

Also asked, how do you clear the error code on a Maytag Bravos washer?

In both the Bravos and Maxima model washers, an "F##" or "F##, E##" code other than those listed indicates a system error. To clear the code, press the "Start/Pause" or "Power/Cancel" button. Restart the washer by pressing the "Start/Pause" or "Power/Cancel" button again.

Likewise, how do I reset my Maytag washer?

Unplug the washer for 1 minute from the electrical outlet.
Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
The motor has now been reset and is ready for you to start a cycle.

Beside above, how do I find the code on my Maytag Bravos washing machine?

Choose any one button on the washer's console except Power, Start, or Stop. Press/Hold 3 Seconds - Release 3 Seconds - Press/Hold 3 Seconds - Release 3 Seconds - Press/Hold 3 Seconds. 4. If there are any saved fault codes they will be displayed.

How do you troubleshoot a Maytag washer?

How to Troubleshoot & Repair a Maytag Washer

Assess the load.
Determine whether the washer is plugged into the electrical outlet.
Remove any kinks from the drain hose.
Close the washer's lid securely to add pressure to the lid switch.
Avoid overcrowding your load; an unbalanced, heavy load can contribute to excessive water fill that can leak.

33 Related Question Answers Found

How do I reset my Maytag Bravos XL washer?

How to Reset a Maytag Washer

Press the "Power/Cancel" button.
Push the appropriate button to choose a new cycle.
Press "Start/Pause." You have now reset your Maytag washer.

How do I fix error f51 on Maytag Bravos?

The F51 error may indicate there is a MOTOR ROTOR POSITION SENSOR FAILURE (RPS). The sensor and control board has a connection or fault issue. This error can be cleared by cleaning/reconnecting the sensor OR replacing it. Make sure the control board and the RPS have a good connection.

How do I fix the lid lock on my Maytag Bravos washer?

How to Replace the Lid Lock on a Maytag Bravos

Unplug your Maytag Bravos from the electrical outlet.
Look for the three screws on the back of the control panel.
Find the wires connected to the back side of the touch control.
Tape the washing machine lid shut.
Insert a putty knife into the top horizontal seam beneath the pencil marks.

What does f5 mean on Maytag washer?

F5 E1. Lid switch fault. Check/ Repair. This code is displayed if Start is pressed with the lid open.

What does lf mean on a Maytag Bravos XL washer?

LF in the display

This means shutting off the water supply, and disconnecting the water inlet hoses from the washer.

What does it mean to calibrate a washing machine?

When you calibrate your Samsung washing machine, you prevent the appliance from vibrating and making a lot of noise. Calibrating your washing machine can be done via the display and takes 3 minutes maximum. This isn't done by default in the factory.

How do I reset my washing machine?

How to reset the washing machine:

Press POWER to turn the washer off.
Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
With the power disabled, press and hold the START/PAUSE button for 5 seconds.
Plug the washer back in, or turn the circuit breaker back on.

What does washer calibration do?

Calibration Mode on Samsung Washing Machines. Samsung washing machines are able to detect the weight of a laundry load automatically. This will help optimise the energy efficacy of the washing machine and reduce the chance of using too much water.

How do you reset a GE washer?

To reset washing machines that use the GE Hydrowave system, start by unplugging the washer for one minute. Plug the washing machine back in and then within 30 seconds, quickly open and close the lid six times. You'll need to do this within a 12-second period.

How do I reset my Whirlpool washing machine?

Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.

How do I reset my Kenmore high efficiency washer?

How to Reset a Kenmore Elite HE Washer

Press the "Stop" button twice, and then press the "Power" button.
Choose a wash cycle (e.g. "Normal"), and then choose your wash options (e.g. "Hot/Cold" or "Cold/Cold").
Press the "Start" button to complete the reset process and restart the washing machine.

How do I reset my Whirlpool front load washer?

Unplug the washer for 30 seconds to attempt to reset the Duet washer control. You can manually unlock the washer by removing the top (remove screws on the back of the top panel and slide the top panel back to lift off.

What does sensing mean on a Maytag washer?

SENSING/FILL Light is on

When the Start/Stop button is pressed, and the Water Level knob is set to Auto Sensing, the washer will fill and begin sensing to determine load size and balance. If the lid is left open for more than 10 minutes, the washer will cancel the cycle and pump out the water.

How do I unlock my Maytag washer?

Reach up along the inside of the front and locate the bottom of the door switch/lock mechanism. Located on the bottom of the door switch/lock mechanism is a tear shaped tab. Gently pull the tab down about 1/4 inch or until a click is heard. The door can now be opened.

How do I reset my Hotpoint washing machine?

Check if the drain hose is clogged, and clear if needed. Turn the machine on with dry hands. If it still won't start, unplug it or turn the circuit breaker off, then back on until the breaker firmly clicks in place and plug the machine into the outlet. Push the restart button.

How do I test my Maytag Bravos washer?

Manual Diagnostic Test Mode. Perform steps 1 and 2 for the activation of the Bravos automatic diagnostic test mode then press the same button one more time while 88 is on the washing machine display for 5 seconds. Pressing the "STOP" or "POWER" button at any time to exit the washing machine's diagnostic mode.