How do you change the depth on a Makita circular saw?

Determine the blade depth by unplugging the saw and holding it alongside your board with the blade guard retracted. Then loosen the depth-adjusting lever or knob and pivot the saw's base until the blade extends about 1/4 to 1/2 in. below the board. Tighten the lever or knob and you're ready to saw.

Thereof, how do you change the blade on a Makita circular saw?

Be sure the blade is installed with teeth pointing up at the front of the tool. Use only the Makita wrench to install or remove the blade. To remove the blade, press the shaft lock so that the blade cannot revolve and use the wrench to loosen the hex bolt clockwise. Then remove the hex bolt, outer flange and blade.

One may also ask, why does my circular saw get stuck? If your hand is asserting a sideways pressure that will cause binding and the saw will stop. Even a slight sideways pressure combined with dirty/dull blade will cause stoppage. When I first starting using my circular saw, 80% of the time I forgot to adjust the depth of cut, making it work harder than it needed to.

Correspondingly, what depth can a circular saw cut?

Circular Saws Parts And Features. These have indicators on them, ?that ?tell you ?what ?depth your cut will be. These can range from 0" and go as deep as 2.75" but usually the maximum depth is around 2.5" or so for most models.

Can I put a diamond blade on a circular saw?

Diamond Blades These types of blades sport a metal blade that's coupled with a diamond or metal composite. Purchasing a diamond blade for your 7″ circular saw can be an ample investment, but you can be sure that it will outlast an abrasive-type blade – it's a perfect choice for those that cut a lot of concrete.

37 Related Question Answers Found

How do you change the blade on a Makita grinder?

How to Change the Disc on a Makita Hand Grinder

Removing the Disc.
With the grinder unplugged, turn the grinder upside down so that you are looking at the grinding wheel and the locking apparatus.
Depress the shaft lock button located on the top of the grinder.
Rotate the disc until the shaft locks in place and no longer spins.

How do I change the blade on a circular saw?

2 Press down on the saw's arbor-lock button and rotate the blade until the locking mechanism engages. 3 Use the blade wrench to remove the arbor nut holding the blade in place. To loosen the nut, turn the wrench in the same direction as the blade cuts. 4 Retract the saw's upper blade guard and remove the old blade.

Where is the arbor lock on a circular saw?

Place the saw on a wooden surface and pull back the blade guard. If the saw has an arbor lock button on the top of the housing, press it in. The arbor is the shaft the blade installs on. If there's no lock button, press the blade into the wooden surface.

How do you tighten a circular saw blade?

In general, the blades on right-handed circular saws turn counterclockwise, so you'd tighten the bolt clockwise; the blades on left-handed circular saws turn clockwise, so you'd tighten the bolt counterclockwise. Hold the outer flange (rim) of the nut with a wrench to keep it from turning.

Why does my circular saw not cut straight?

If you are struggling with the circular saw to cut straight line on the wood, at first, look at your workpiece. So, if you find out that your saw is okay and the problem is with your unstable wooden piece, just have a set of hold down clamp. It will lay hold on the workpiece with the table to make it stable.

Can you use a 7 inch blade on a 10 inch saw?

A smaller saw blade may reduce kickback injuries, says Bob Chase. At Chase Cabinets, owner Bob Chase makes the case is simple: Replacing the 10-inch blade on a table saw with a 7-1/4-inch blade can bring immediate benefits.

Will a circular saw cut a 4x4?

Most circular saws sport a 7 ¼” blade which has a cutting depth of up to just over 2 ½” at 90 degrees and usually less when cutting bezels. The smaller 6 ½” blade cuts to a max depth of 2 1/8″. This means that the two most common blades are not large enough to go through a 4×4 in a single pass.

Why does a circular saw kickback?

Kickback happens when the saw blade binds or stalls suddenly in the wood and the saw gets driven back toward you. So the key to preventing this is to make sure your blade doesn't bind in the wood.

How do you set the depth on a circular saw?

Determine the blade depth by unplugging the saw and holding it alongside your board with the blade guard retracted. Then loosen the depth-adjusting lever or knob and pivot the saw's base until the blade extends about 1/4 to 1/2 in. below the board. Tighten the lever or knob and you're ready to saw.

Can I use circular saw to cut concrete?

Use a standard circular saw, equipped with a corundum or diamond blade, for small tasks. For slabs, it's best to cut through the top inch, then use a sledgehammer to break off the rest. The jagged edge left below the cutting line provides a good rough edge for the new concrete to bond to.

How do you cut straight with a circular saw?

To ensure a straight cut, press the saw firmly against the straightedge as you push it along. Clamp a perfectly straight board or metal straightedge to a sheet of plywood to make cabinet-quality straight cuts.

When using a circular saw is it sure to cut?

guard protects you from touching the blade. When using a circular saw,be sure to cut on the waste side of the cut mark to allow of the blade's.

How do you use a circular saw without a table?

How to Use A Circular Saw Without A Table

Step 1: To start off, you should get a pressure treated plywood or some sort of wood which has a high moisture content.
Step 2: Fit your saw with the edge guide.
Step 3: Next, you've to set the depth of the blade accurately.
Step 4: After that, place the unused pieces of wood on the sawhorses.

What is the max cutting depth of a circular saw?

?Circular Saws Parts And Features. These have indicators on them, ?that ?tell you ?what ?depth your cut will be. These can range from 0" and go as deep as 2.75" but usually the maximum depth is around 2.5" or so for most models.

How deep can a 7 1/4 inch circular saw cut?

Specifications

Input	120V AC, 15.0 Amps
Blade Diameter	7-1/4”
Depth of Cut Capacity	0°.2-3/8”
	45°. 1-3/4”
	51.5°. 1-5/8”

How do you keep a circular saw from binding?

Avoid circular saw blade binding

You can hold one end, but the other must be free to drop or the blade will bind. The trick is to allow the cutoff end to drop slightly, but not so much that it completely snaps off before the cut is complete. One method is to support the board with strips of wood as shown here.

Why does my circular saw burn the wood?

A Dull or Dirty Saw Blade Might Be the Culprit

Pushing the stock through the saw too slowly is a common cause of saw blade burn. Sometimes a blade that feels dull might only be dirty. If wood pitch resins build up behind the teeth of the blade, the cutting speed will slow down, increasing the chances for burns.