How do you bypass a zone on first alert?

Asked By: Zoher Laphizmendy | Last Updated: 3rd April, 2020
Category: home and garden home security
4.6/5 (258 Views . 22 Votes)
Bypass a Zone
  1. Enter the following: Your 4-digit code. The number 6 (bypass button) Two-digit zone number of the zone you want to bypass. (01, 02, 03, etc.)
  2. Repeat this process for all zones you would like to bypass.
  3. Once your system is disarmed, this process will need to be repeated in order to arm your system again.

Click to see full answer

Considering this, how do you bypass a zone on ADT alarm?

Steps for Setting a Bypass Zone on ADT Systems

  1. Enter the function menu by pressing “*”
  2. Keyboard will display “Press * for Zone Bypass”
  3. Press “1” or “*” to enter bypass mode.
  4. Select 'Zone Bypass' and enter your access code (if required)
  5. Enter the zone number (between 01-64) that you wish to bypass.

Also, how do you remove a zone from an alarm system? To bypass a zone on your alarm system:

  1. Enter the following: Your 4-digit code. The number 6 (bypass button) Two-digit zone number of the zone you want to bypass. (01, 02, 03, etc.)
  2. Repeat this process for all zones you would like to bypass.
  3. Once your system is disarmed, this process will need to be repeated in order to arm your system again.

Herein, what does Zone bypass mean?

Bypass is the term used to describe the ability to deactivate specific zones of the alarm system before arming the system. Bypassing allows for certain areas to be disarmed while the rest of the space is armed. The system will not allow Panic, Fire or CO zones to be bypassed.

How do you delete a zone on a Honeywell alarm system?

Remove a Honeywell wireless zone by entering zone programming, setting the zone/response type to 00 or "New". Then confirm that you want to delete the zone when prompted by the alarm panel. Once the zone has been deleted from programming, it can physically be removed from the system.

25 Related Question Answers Found

How do I reset my alarm system?

How to Reset a Home Alarm System
  1. Check the manufacturer's website for installer instructions.
  2. Check out do-it-yourself alarm support sites (see References below).
  3. Locate the power source to the Main Control Panel.
  4. Disconnect the backup battery in the Main Control Panel.
  5. Leave power off for a minimum of five minutes.
  6. Reconnect the battery leads.

How do you clear an ADT fault?

The security system may need to be reset by entering your code into your system and hitting off twice. Remember to remove the system from Test Mode. Go to and click on My Alarm from the System Management option, select Stop Test to remove the system from test mode and restore operations.

Can home security systems be hacked?

Yes, security systems can be hacked into just like computers. A burglar can hack into your security system, deactivate the alarm, enter your house and get away with the goods without leaving a trace.

How do I bypass alarm zone IDS?

Hold down the [9] key until the keypad buzzer sounds to enter bypass mode. 3. Press the number corresponding to the currently bypassed zone, then press the [E] key.

What does Zone faulted mean?

Faulted is a generic way of describing a status that could trigger an alarm. You may also see Bypassed if the zone is being ignored so that the system can be armed without a faulted sensor trigging an alarm. For example, you may want to leave a window open (faulted), but still arm the security system.

How do you bypass a motion sensor alarm?

Move slowly along the walls in which the sensors are located, and as low as possible, while proceeding forward. Many motion sensors have blind spots that make it difficult to detect movement directly underneath them. Be aware that another sensor may be pointing in your direction from the other side of the room.

What does bypass sensor mean?

Bypassing a sensor allows the system to remain armed while leaving a specific sensor (or sensors) in a disarmed status. For example, if an individual wants to arm their doors and windows but leave a kitchen window open, that sensor can be bypassed.

How do you disable a car alarm from the outside?

7 Ways to Turn Off a Car Alarm
  1. Try starting your car.
  2. Hit the panic button (again)
  3. Remotely lock or unlock the car.
  4. Use your key to physically open your driver's side door.
  5. Open the trunk (or use other buttons on the remote)
  6. Remove the alarm fuse.
  7. Disconnect the vehicle's battery.
  8. Check the owner's manual.

How do you bypass a car alarm?

Part 1 of 1: Turning off a car alarm
  1. Materials Needed.
  2. Step 1: Familiarize yourself with the alarm.
  3. Step 2: Start the car.
  4. Step 3: Use your key to unlock the driver's door.
  5. Step 4: Pull the fuse.
  6. Step 5: Disconnect the battery.
  7. Step 6: Maintain your key fob.

What is an alarm zone?

Basically alarm zones are how a security system manages and controls sensors. The sensors are assigned to zones and when a sensor is trigger the system informs you which zone a sensor has been triggered. The control panel may also “speak” to you to let you know the zone where the security event took place.

How do you disable a window sensor?

Yes, you can disable a window alarm sensor. A window sensor can be temporarily disabled by bypassing the associated zone. You can also permanently disable the sensor by deleting its zone from programming. You will need to re-enroll the sensor with the system if you want to use it again.

How do you disable an alarm sensor?

Enter the password programmed into the control panel earlier so that the home alarm lets you access the menu commands. Navigate to the menu that will let you deactivate the window sensor to be disabled. Deselect or remove the check mark next to the window sensor on the "Input" menu.

How do you remove an alarm sensor from a door frame?

Complete the following steps to remove an alarm sensor from your door:
  1. Clear the zone. Go to your panel, and delete the zone from the panel.
  2. Remove the wires. If you have a hardwired door alarm sensor, then you must disconnect and remove the wires.
  3. Take off the sensor.
  4. Take off the magnet.

How do you silence GE Simon XT?

Press DISARM, the display shows “ENTER CODE”, then enter your code. The panel will then display or say “Disarmed” and the DISARM button will light up. Silent Button – Press to silence exit beeps when arming.

What is Frontpoint security?

A. Frontpoint is the only nationwide alarm company to have deployed 100% wireless/cellular security systems for every customer. That means our system is not dependent on your phone line, internet connection, or any other system in your house.