How do I run a sprinkler pipe under my driveway?

Asked By: Aines Edgar | Last Updated: 18th January, 2020
Category: business and finance construction industry
4.8/5 (40 Views . 44 Votes)
Cut a piece of 1 3/4-inch PVC pipe 6 inches longer than the width of the driveway. Slide one end of that PVC pipe into one of the trenches. Slide the brass sweeper nozzle on the smaller pipe into the other end of the 1 3/4-inch pipe. Turn on the water to pressurize the 3/4-inch pipe.

Click to see full answer


Moreover, can I put a driveway over water lines?

Driveways are installed over water supply lines and sewer lines all the time. It would be an infrequent occasion ever to need to excavate these lines. In no event, should pavement be installed over a septic tank or its drain field.

Additionally, how do you bore a hole under a driveway? Push the tip of the drill into the end of the trench, allowing water pressure to bore into the soil. Continue pushing the drill under the driveway until the tip comes out the other side. Work the drill back and forth to clear debris from the hole, if necessary.

Consequently, how do you run a drip line under sidewalk?

Push the pipe forward and then pull back as the water tunnels through the soil under the sidewalk. Continue to push and pull the pipe under the sidewalk until the pipe trench is cut and the pipe is completely beneath the sidewalk, extending about a foot on each side.

How do you drill into concrete?

With a water hose, a little time, and $179.95, you can dig under concrete!

In six simple steps you can dig under concrete:

  1. Attach drill pipe.
  2. Connect garden hose.
  3. Dig a small ditch.
  4. Start your bore.
  5. Add more drill pipe (if necessary).
  6. Pull piping through.

27 Related Question Answers Found

How do you tunnel under a driveway?

Lay the pipe in the trench with the open end pointed toward the driveway. Put on your eye protection, because the water may throw back mud and small stones as it digs. Turn on the water full blast. It will immediately begin to tunnel into the soil under the driveway.

How do you install a sprinkler system?

  1. plot types and locations of sprinkler heads. Plan the System.
  2. install an anti siphon valve. Access the Water Line.
  3. dig the trench for system.
  4. attach one end of valve manifold assembly to water.
  5. attach risers using 90 degree connectors.
  6. level sprinkler heads with soil level.
  7. timer controls length and frequency of waterings.

Can you drive over buried PVC pipe?

Re: Driving over Schedule 40 PVC
With little pipes, a foot of dirt over it will carry anything you can drive over it if the soil has been compacted after filling the trench. If the soil is new, and loose, then it doesn't do anything to carry the load and the pipe may be damaged from movement.

How do you fix a broken sprinkler pipe under concrete?

  1. Dig up the area on both sides of the concrete until you expose the supply pipe.
  2. Shut off the water to the sprinklers at the main ball valve.
  3. Cut off the pipe on both sides of the concrete using a hacksaw.
  4. Pull the damaged pipe out from under the concrete.

How do you install a trench drain in a driveway?


Cut the asphalt or concrete a minimum of 12 inches wide; go wider if your surface is uneven. Remove cut material and dig a square trench 7 inches deep. The drain will be sized and shipped to you in 4 foot sections. Pin sections together on a flat surface, pick the drain up as one unit and set in the trench as shown.

How much does it cost to install a channel drain?

Also, the channel material and grate type (plastic, metal or precast concrete) used can impact overall price. For these reasons, trench drains can range in cost between $30 per linear foot to $150 per linear foot.

How deep can you bury corrugated drain pipe?

Dig a 14-inch trench where you plan to run your corrugated drainage pipe. The trench should end at least 6 to 8 feet away from the home.

How do you run electrical wire under concrete?

How to Run Electrical Wire Under Concrete
  1. Select a pipe of sufficient diameter for the desired excavation width.
  2. Dig a small trench on each side of the concrete slab.
  3. Measure the width of the concrete slab.
  4. Push the angled end of the PVC pipe into the soil in the trench on one side.
  5. Tap the other end of the PVC pipe with your sledge hammer.

What is a linear drain?

Linear drains work by allowing the water to flow through the drain and into a trough, or channel, beneath the shower floor, where it enters the regular drainage system. Leading linear drain manufacturer Infinity Drain supplies drains that will work with any size shower.

Can my driveway go over my gas line?


Streets, driveways and sidewalks are built over gas lines everyday. Just dont dig down and hit it, the new lines are yellow plastic tubbing, they will flex and stretch.

How much weight can schedule 40 plastic PVC take?

How to use our Load Deflection Chart:
Horizontal Span Length (ft.) 1/2" Size 1" Size
1' 18 lb. 40 lb.
2' 5 lb. 24 lb.
3' 3 lb. 11 lb.
4' 2 lb. 6 lb.

Can you drive over drain tile?

Yes, you can drive over the drain line once buried with rock provided the item is like a pickup for weight. If we do the math - weight bearing down on surface areas - a 4000 lb. truck puts as little PSI on the soil surface as I would standing on the ball of one foot.

How do you hide irrigation pipes?

You can keep pipes hidden by burying them in the ground. I have an intake that runs into the sand of the shore, and every other pipe after that is subterranean. Listen for the sound of pipes snapping to each other and use a vertical pipe to see where the endpoints are.