How do I program my orbit 6 sprinkler system?

Asked By: Heraclides Kopcke | Last Updated: 20th March, 2020
Category: home and garden smart home
4.5/5 (68 Views . 16 Votes)
Programming 6-Station Timers
  1. Turn the dial to "Cycle Start Times."
  2. Press the "+" or "-" to set the start time.
  3. Press "Enter" to confirm the start time.
  4. Press "Next" to set the start time for each additional program, following the same procedure.

Click to see full answer


Just so, how do you program a orbit 6 sprinkler timer?

Programming 6-Station Timers

  1. Turn the dial to "Cycle Start Times."
  2. Press the "+" or "-" to set the start time.
  3. Press "Enter" to confirm the start time.
  4. Press "Next" to set the start time for each additional program, following the same procedure.

Beside above, what is budget in orbit sprinkler system? between the actual time and the remaining hours of the. delay, every 2 seconds. Water Budgeting. Water Budgeting is a simple way to adjust your watering duration to match seasonal watering needs . Water Budgeting works by increasing or decreasing watering duration for all stations in each program .

Beside above, how do you test an orbital sprinkler system?

From the Timer Box

  1. Turn the dial to the "Auto" position and press the "Manual" key to test the valves on Easy Dial and Easy Set Orbit timers.
  2. Turn the dial to the "Auto" position and move the slide switch for the desired valve up to the "Manual On" position to test valves on Orbit's "Individual Station Slide" timers.

How much water does my lawn need?

Your lawn needs at least 1”-1 ½” of water per week, year-round, during the winter, too. Water deeply 2-3 times per week, rather than daily. Water as early in the morning as you can, when possible. If you can't push a 6” screwdriver into your lawn, you're not watering enough.

28 Related Question Answers Found

Why is my orbit Sprinkler not working?

If one or more of the sprinklers is still not working, contact the installer of the system, as you may have an issue with the hardware. Remove any dirt or debris from the valve of a sprinkler that will not shut off once turned on, as foreign items in the sprinkler may cause it to stick.

How do I reset my orbit timer?

Reset to Factory Default – Orbit Irrigation B-hyve Help. To reset your timer back to factory settings: Turn the timer to the OFF position by rotating the dial. Open the front swing panel and press and hold the reset button for 10-12 seconds.

What does no AC mean on orbit sprinkler timer?

The NO or NO AC display is a diagnostic message telling you that the controller has stopped receiving AC power. The controller is running on the power supplied by the backup battery. Check the power source by plugging a lamp or radio into the wall outlet to verify there is power at the outlet.

Why does my orbit sprinkler timer says off power?

Why does my timer show “off pwr” in the LCD display? This can be caused by: • Disconnected power supply. A blown fuse (in some models). Programming Note: To conserve water, Orbit® timers are equipped with a rain delay feature.

How does orbit rain delay work?


[RAIN DELAY] allows you to delay your sprinkler timer from watering for a set period of time . Delay settings are 24, 48, and 72 hours . If a longer Rain Delay is desired, press the [+/–] buttons to increase or decrease the setting .

How do you test a sprinkler solenoid?

How to Test Sprinkler Solenoids
  1. Turn off the water supply. Open the bonnet of the sprinkler valve and unscrew the solenoid, taking care that you don't drop the plunger and the spring.
  2. Open the solenoid housing and inspect the plunger.
  3. Reinsert the solenoid plunger into the housing.
  4. Turn on the water and test the sprinkler.

How do you test a sprinkler valve?

To determine if the valve is receiving power, use a volt-ohm meter. From the irrigation controller, manually turn on the station you are troubleshooting. With the volt-ohm meter, check the voltage between the ground and the controller-station terminal. Your reading should be 24 volts AC (VAC).

How do you adjust orbit brass sprinkler heads?

Insert a flat-head screwdriver into the slot of the screw in the center of the nozzle and turn it clockwise to reduce the spray amount and distance. Turn it counterclockwise to increase them. Adjust the spray pattern on a gear-driven sprinkler using the screwdriver.